f2 error on spa Girdletree Maryland

Address Ocean City, MD 21842
Phone (443) 373-7442
Website Link
Hours

f2 error on spa Girdletree, Maryland

If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Doing so may cause damage to the pump and cause the system to go into an overheat condition. You need to try and release any air bubbles in your circulation try cracking a seal in a union to release the air or you can also force water through intakes Back to Top OHH, HH, or HTR TEMP LMT SERVICE REQD Message There is an "Over Heated Heater" (OHH or HH) Condition.

Closed Slice Valve. If there is No Error Message, Select "No Error Message" Below. A: When you see this on your control, rest assured, nothing is wrong. Heat Related Pump Not Running.

Sign in to follow this Followers 0 Spa Control Panel Codes? Any and all servicing should be performed by a licensed spa technician. Q:My control panel reads the error code "SN1." What do I do? Dave.

Spa temp over 108°.  HLoH : Hi Limit Over Heat. The Water Temperature is Sampled Only during Programmed Filter Cycles. Making the most of your Backyard Heaven! Spas with Pump Suction Blockage Switch: The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment

Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode. If you have a Circ Pump, do this first (EL version): - Push the Jets 1 button once. Some Spa Brands or Models may have this Message Enabled, and the Interval between these Messages will be whatever the Spa Manufacturer has selected. drops HL: High limit switch tripped EasyPak Error Codes C: Celsius CL: Current Time of Day ECdu: Econo Mode Duration Econ: Econo Mode Turn On F: Fahrenheit Fldu: Filter Cycle Duration

Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode. Unless the water is very cold, only the circ pump will start for one minute. Check for All of the following Conditions: Low Water Level. Ecn or Ec is ON Solid (Not Flashing): The Current Water Temperature is "Unknown" (- - - or - -) while in Economy or Sleep Mode.

If they're not, or you're not sure that both are (because you can't tell whether you have two separate flows at different rates or just one flow), momentarily turn both pumps Water temp has reached 118ºF. Check for All of the following Conditions: Low Water Level. Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).

If there is Now an Error Message, select Message Other than PSt or Persist Fail below. Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation. Note: The Balboa Default is to have this Message Disabled. The "CF" code is simply a countdown timer that has reached zero is there to remind you to clean your filter.  To reset your clean filter reminder, simply refer to "CF"

Resting and Relaxing in Calabria Italy. Any info would be helpful. Generated Sat, 15 Oct 2016 13:34:23 GMT by s_ac15 (squid/3.5.20) Jump to content Portable Hot Tubs & Spas Existing user? System will restart when temp.

Back to Top rSA or CK SANITIZER Message Time to Check "Sanitizer Level Reminder" (rSA). The Real Time Clock keeps the Current Time of Day. If there is Now an Error Message, select Message Other than rtC or RTC FAILURE below. The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub.

I'm not familiar with "C1" on any Balboa control box. "IC" indicates a water temperature of 44 degrees or lower has been detected. "F2" is a filtration cycle. You are here:HomeHome/GardenHome AppliancesHot TubsCal Spa Codes Hot Tubs/Cal Spa Codes Advertisement Expert: calsparepair - 1/17/2010 QuestionCan you tell me what the code C1, and F2 mean? A: This is very much like our "CF" where nothing is actually wrong. If there is No Error Message, Select "No Error Message" Below.

If Not, Continue to Next Step. During Heating, this message indicates a Possible Low Flow Condition. Brett Aqualine Error Codes OH: Temp exceeds 118 F Fr: Freeze condition - temp below 40 degrees FL: Pressure switch failure EO: Shorted temp sensor E1: Open temp sensor E2: Shorted Family History.

All Reminder Messages can be Disabled through the Topside Panel Users Menu. * Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different. Click here for instructions LOADING... /HotTubAssist 689 @HotTubAssist /HotTubAssist 0800 849 2468 01245 392 630 [email protected] TOP about us services services home delivery repair services bronze, silver and gold service options However, if you would like to trouble shoot a little more over the phone then please call us at (858) 675-7727. A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!

Closed Slice Valve. If the SnS or Sn Message is Blinking or Flashing OFF and ON without showing Water Temperature, it is a Verified Sensors Out of Sync Message. Registered office: Hitachi Capital House, Thorpe Road, Staines-upon-Thames, Surrey, TW18 3HP. If the spa goes through the typical Overheat Errors and continues on to exhibit specific temperature-rise-over-time requirements, the system will assume a pump relay is stuck ON, and has no ability

If the spa is subsequently powered down and then powered up again, the HOt message will appear on the display and the spa will not be allowed to operate until a With a pH Sensor Installed in the System, the pH Level is Above 7.8 and needs to be Corrected. A: This is usually a hi-limit sensor. Hot Tub Care in the Winter 101 Beachcomber Hot Tubs Error Codes & Information Hot Tub Filters - When To Clean & When to Replace Archives Archives Select Month August 2016

This indicates a Possible Problem with the System Board. If your display is stuck at "F2" press the Jets buttton. Back to Top rCH or NEW FILTER Message Time to "Change Filter Reminder" (rCH) Appears Every 365 Days*. Spa Water Cool Down In order for the Spa Water Overheat Error Message to Automatically Reset and Clear, the Spa Water Must Cool to below 108°F (42.2°C).

Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. It is the small metal sensor attached to the side of the heater tube. Arctic Spas backyard barbecue BBQ bbq chicken buying a hot tub cover cedar deck change filter chemicals cover cap error codes facebook facebook free contest fire pit grill hot tub hot All Rights Reserved.

If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because