fix raid 1 error New Limerick Maine

Address 117 Main St, Houlton, ME 04730
Phone (207) 521-0002
Website Link http://www.dnkmedia.com
Hours

fix raid 1 error New Limerick, Maine

Dina synpunkter har skickats. Tags: NAS / RAID Boot Storage Last response: 19 November 2010 20:31 in Storage Share ahthurungnone 6 October 2010 22:20:20 I have two drives installed using RAID 1. What do I do now? Keep up the good work.

From: Bob Gustafson Reply Excellent HowTo - thanks much.

Försök igen senare. m 0 l sminlal a c 415 G Storage 20 October 2010 00:31:03 Well as I said, the safest way is to have tested it ahead of time so you know Go to All Programs\Intel Matrix Storage Manager\Intel Matrix Storage Console to launch the Intel Storage Console. Q: If a disk is slowly failing, will it be obvious which one it is?

Thank you. m 0 l ahthurungnone 8 November 2010 19:33:44 So I am today going to copy all data to my backup drive. The raid utility says the drive in port 1 is bad, so maybe I just need to check the EVGA mainboard manual to see if one of the SATA plugins is Publish Related resources SolvedRAID 1 Failure: one drive "error occurred" other "offline member" Forum SolvedI have a Dell XPS computer running Win 7 and a RAID 1 array of 2 WD

You have a 50/50 chance that your Bios is pointing to the blank disk. How to fix? What kind of hard drive? Thanks

From: mike Reply hello,it is great,but will theMBR also been copy to the new hd ?

RAID has been working for years, but I made ths mistake and now that disk cannot rejoin the raid. Why do I mention that? Click Intel Rapid Storage Technology. If you're wondering what's changed in the storage market after the past few years, there has been some...

Disk /dev/sdb: 2000 GB, 2000396321280 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 The problem is I am not sure how to fix this.First, am I correct in assuming one of the drives is bad? Recently, the disk with /dev/hdc3 failed, and was replaced with a new disk. Using it I was able to "rebuild" the array by adding the out of sync disk back into the logical device.

How do I proceed? If you're still not sure which drive to physically remove, run a badblocks scan on the drive that was removed. This is for moving to a different controller, but I see no reason that it should not work for moving drives on the same controller. During boot it cites that one drive has a Critical Error.

Can you be more specific? Lenovo driving me mad Hot Network Questions "Rollbacked" or "rolled back" the edit? A RAID Degraded error message after POST? My only question when working through the tutorial was is it necessary to --fail all of the remaining partitions on a disk in order to remove them from the array (in

more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Evey time my server reboots it seems to put the drives in diffrent dev nods. (ex, sdb1 is now sda1, and so on) Not everyone can dig though the commands for A: The newer tools drop support for this flag, replacing it with the --force-resync flag. Why is water evaporated from the ocean not salty?

Thanks! 2 - In my case, when I shut down, removed the failing drive (and did the above mapping and labelling!), and then rebooted - the removes had been done for So, the article says this: "You can also run cat /proc/mdstat and instead of the string [UU] you will see [U_] if you have a degraded RAID1 array." Yes, that's right Do you have a Random Array of Independent Disks (RAID) configured on your PC? Exactly what I needed to add to my toolbox.

Disaster averted!

From: Mark Copper Reply Worked for me, too. And, unless you ran fsck in "verify only; do not update" mode, its quite possible that you have corrupted your data. Read the popup message carefully, to be sure that you are not copying in the wrong direction!!! The new disk can have the same or a bigger capacity than the failed disk, but not a smaller capacity.

m 0 l Related resources Raid 1 Goes Critical - Drive Seems to have "Rolled Back" a month - Forum CRITICAL_ERROR leads to RAID 1 issues? - Forum Updated to Windows A: If you are concerned about RAID, High Availability, and UPS, then its probably a good idea to be superstitious as well. It was very useful to me.Just one thing I would add, when you explain how to copy the partition table, I would make a BIG note stating that one should have The disks were connected to connected to a AMD SB710 controller and the server was running Centos 5.7I did have problems getting the system to boot from sdb ( fixed by

type 'install (hd1)' 9. Why is it a bad idea for management to have constant access to every employee's inbox? If I am going to do all this work, should I just install one drive to run the OS and two drives to run RAID with the important company data (this Get the answer sminlal a c 415 G Storage 14 October 2010 04:45:52 You should be able to simply shut the system down, remove the failed drive, replace it with a

How much interest should I pay on a loan from a friend? Forum SolvedRandom Windows 8.1 Critical_Process_Died Error Forum RAID Error. If not, you'll need to find documentation for the RAID controller. This guide made good sense and I was able to proceed confident I understood what I was doing.

Make a backup of your data to a separate drive - not the other drive you plan to RAID with. Please refer to our Privacy Policy or Contact Us for more details You seem to have CSS turned off. Thus, you can experiment with different possible repair schemes. Full Review be quiet!