fix cd player no disc error Millinocket Maine

Address 248 Maple Rd, Atkinson, ME 04426
Phone (207) 717-7097
Website Link
Hours

fix cd player no disc error Millinocket, Maine

Veröffentlicht am 29.04.2013how to repair no disc error in dvd ,cd player Kategorie Bildung Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen... Top Log in or register to post comments Fri, 08/22/2014 - 16:54 Permalink evil Try cleaning the laser eye Try cleaning the laser eye with rubbing alchohol on a q tip. It turns on I cleaned a dvd of finger prints and inserted it into the machine, it starts turning like it is going to start and about 4 minutes later is Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

On video discs this will cause skipping, jumping or macro blocking (big squares on the screen) as a result of the software trying for too long to re-read the difficult section. Angle the disc so that you can see the surface clearly and not just reflections. TwiddlerTM and Full-Range Driver Replacement 8.1 Solder the red wire to the positive (+) driver terminal and the black wire to the negative (-) driver terminal. 8.2 Align the driver (3, When you hit eject peck on the tray very hard and see if it pops out.

For example, you cannot play the DVD disc format in a CD player. Nächstes Video How to clean a DVD or CD player or recorder lens "Sony RCD-W500C" - Dauer: 4:49 OldSchoolTechCorner 243.039 Aufrufe 4:49 Simple dvd fix that engineers use - Dauer: 9:05 I cleaned the lens, adjusted the small screws on the laser pickup but no luck. A.

It stopped reading DVD's a while ago. Display PCB Removal 3.1 Perform procedure 1. 3.2 Lift up the display PCB (1). 3.3 Remove the ribbon cable that connects the CD door (7) to the display PCB. I would highly recommend a Blu-ray CD player. There's a couple of ways to do this.

Use your fingers to open the disc tray door slowly and gently. I think this unlikely, but I would appreciate hearing from those with more experience than I have. If you have established by inspection that there is simply too much damage to the reading surface of the disc click here to go to the Tutorial on How to Repair What this means is that the CD player, for some reason, does not recognize the disc.

Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Anzeige Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt. Open the top disk cover with the player off and all batteries out and unplugged, and move the lens mechanism if you can. Terms of Use Privacy Policy Copyright Policy "Do it yourself video editing for the enthusiastic amateur" A Step by Step Guide to DVD CD or Game Disc Repair A Step

After running the cleaning disc, the player read dvd's again. Kategorie Wissenschaft & Technik Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen... Top Log in or register to post comments Fri, 08/22/2014 - 16:53 Permalink mississippi I bought a collection set of I bought a collection set of the tv show "3rd Rock Top Log in or register to post comments Fri, 08/22/2014 - 16:54 Permalink dibloff Hi everyone.

It was still reading CD's. Cleaning the DVD Laser Lens Step 1Power off the DVD player and disconnect all cables. Step 3Reconnect all cables to the DVD player and power on the device on again. Jammed In-dash Ford 6 CD Changer Repair - Dauer: 40:50 The Workbench 180.727 Aufrufe 40:50 Reparación de un DVD ¡ No lee Discos ! - Dauer: 6:01 Leo Sanzeh 704.508 Aufrufe

So normally when you insert the disc it "grabs" it and takes it. If not, then continue with the instructions. For me no disk is usually means that the tray or the disk isn't quite in position; a couple taps and jiggles usually works. In a repair shop, they probably change the transport module if they see a problem there rather than try to take it apart.

You can change this preference below. I've got a Sylvania SDVD 8730 portable dual 7" DVD player. This is most often attributable to disc being left in strong light for extended periods of time or by using RW discs that have begun to fail. Anzeige Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt.

no caps are swelled. These two components are in constant use and wear out the most. Common error messages such as Disc Error, No Disc, Invalid DVD Navigation or even Invalid File Structure tend to make you think you have a problem disc… not a problem reader. it worked good for the past 3 years . . ..

Also try multiple CDs and jiggle them around to make sure they're properly seated. NO DISC error on a CD / DVD player If you are getting a NO DISC error on a CD / DVD player, then chances are the laser has failed. Hinzufügen Möchtest du dieses Video später noch einmal ansehen? It can be any number of things.

Wird geladen... Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen. Top Log in or register to post comments Fri, 08/22/2014 - 16:55 Permalink jkeasley You can find some information You can find some information here: http://is.gd/no_disk_error Top Log in or register Hinzufügen Möchtest du dieses Video später noch einmal ansehen?

I did....twice Reply With Quote 05-30-2013,10:33 PM #11 menschenstimme Forum Regular Join Date Mar 2013 Posts 66 I can handle the loss. Good luck folks! Again, this is all empirical without any diagnostic equipment nor meters of any kind. But with one particular pair of contacts the motor did twitch slightly - for what this information may be worth . . .

it has not taken any damage. If cleaning the lens does not solve the problem then I make sure the laser is working. Most of those early CD players would be hard to find as they often ended up in landfill. I removed the motor and took a small 12-volt DC source and touched the leads to the motor's several contacts.

This made no improvement. Cancel 4 Answers Filter by: Most Helpful Newest Oldest Most Helpful Answer oldturkey03 @oldturkey03 Rep: 366.9k OTS 578 263 1k Posted: 01/15/2013 Options Permalink History Crys, if you cleansed the lens Main PCB Replacement 12.1 Lower the main PCB (1) into the base. Inow understand why it said no disk is because it was running half speed in stead off full soead to read the disk bonzo Top Log in or register to post

Reply With Quote 05-30-2013,09:52 PM #8 Smokey VIP Member Join Date Jan 2004 Location Ozarks Posts 3,947 You might get a kick out of this as I ran into same problem The bill was about $400. Burning errors create the same effect with the data not recorded correctly on the burning surface of the disc and throwing confusion into the situation. Back in the 1990s, I used to fix many of these and it was always either the spindle motor or the laser that failed.

This player was 3-5 months old when it stopped playing.