fax ng error codes Lawtell Louisiana

Our mission is to make the most out of your computer systems. Our company provides sufficient computer system repairs, updates and services at a reasonable cost. SuperTech Computer Service is here to help your computer system(s) run smoothly. We offer computer remote support, on-site service and in-shop service. Call us at 337.948.0019 to see how we can help you.

Address 904 Creswell Ln, Opelousas, LA 70570
Phone (337) 948-0019
Website Link http://www.supertechcomputers.net
Hours

fax ng error codes Lawtell, Louisiana

Cause: The other party released the line Solution: Retransmit B. Solution: Have the other party boost the transmission level for proper reception of the picture signals. Solution: Adjust the NL equalizer so the other party can receive picture signals properly. Solution: Boost the transmission level so the other party can properly receive TCF.

B. Confirm that the local user really wants to attempt a poll reception. Cause: Insufficient loop current. A.

A. Cause: Cannot receive phase signal properly due to poor line conditions. There was a communication error with the sending fax machine. Solution: Have the other party boost the transmission level to receive the picture signals properly.

Solution: Leave powered ON for 5 days, battery will recharge, but data has been cleared. Cause: Defective DTMF IC; (does not go into ready mode). Z7_3054ICK0KGTE30AQO5O3KA3015 hp-online-communities-portlet Actions ${title} Loading... A.

A. C. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##707 [ TX ] NSC transmission speed command error during ARQ transmission. B.

If the session fails after sending several pages of a large document, resend the document as several smaller documents. Cause: Cannot receive picture signals properly due to poor line conditions. Solution: Boost the transmission level so that the other party can receive carrier signals properly. Cause: Volume of encoded data very large, due to too many fine lines in document.

That's what it said on the transmission report. A. Solution: Set the document and have the other party call again F. The email address entered is already associated to an account.Login to post Please use English characters only.

A. See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Cause: Other party cannot receive DIS signal properly due to poor line conditions. The error code is also printed next to "NG." NOTE If an image is not attached, appears below the title.

Solution: Take echo counter-measures as described in Service manual. A. Source(s): received quot ng quot error send fax canon mx860 mean: https://biturl.im/jKsTP Jimmie · 1 year ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now A.

Solution: Lower the transmission start speed to 4800 bps. Cause: Defective internal unit. Solution: Boost the transmission level so the other party can receive the signals properly. Solution: Replenish recording paper.

A. This error might be associated with bad line conditions or might indicate a problem with the fax's modem. Please enter a valid email address. Cause: STOC detected an abnormality Solution: Call NTT notifying them of the trouble E.

If the error persists, and error correction is in use for the fax session, disable ECM. Cause: Abnormal protocol. Cause: The operation of the UPI to control the G3 modem did not finish properly. Solution: Retransmit. ##224 [ TX / RX ] Abnormal protocol during G3 communication A.

The local machine held the remote machine during reception of a large or complex document due to lack of available memory. Configure the machine to start reception at a lower speed. Cause: The other party cannot receive signals properly due to poor line conditions. A.

Solution: Perform echo counter-measures listed in service manual Solution: Lower the transmission level to prevent echo reception of the transmitted CFR signal. ##294 [ RX ] Fail to receive If the machine still does not operate normally, turn the main power OFF, and then back ON. (See "Before You Start Using This Machine.") #706 Cause 1 The Address Book is Cause: Usually--cannot receive picture signals properly due to poor line conditions. B.

Try to verify this by sending the same fax to other fax machines. Reduce or enlarge the page size setting on the local machine to a size supported by the remote machine. 319 The local machine attempted to initiate a binary file transfer (BFT),