floppy disk error code Ozawkie Kansas

Dell Registered Partner selling Dell computers and equipment wholesale, computer repairs all PCs, professional custom website design and services, QuickBooks setup and training, marketing and bookkeeping consulting, data security and backup services, and graphic design services.

 Commercial and government consulting services in technology, data storage, data backup, QuickBooks consulting, marketing, and website services including design and hosting. 

Address Holton, KS 66436
Phone (785) 364-2018
Website Link http://bizmd4u.com
Hours

floppy disk error code Ozawkie, Kansas

Once at the prompt, place a diskette into the floppy disk drive and type format a: if you get: Invalid media or Track 0 Bad - Try formatting another floppy disk. In some situations, the PnP logic is not able to resolve all the system's resource needs and a configuration error occurs. Do you want to format it now? PRESS F1 TO DISABLE NMI, When BIOS detects a Non-maskable Interrupt condition during boot, this F2 TO REBOOT will allow you to disable the NMI and continue to boot, or you

They say taht they believe the operating system has been corrupted. Thank you 0 #8 Zach Kemppel Posted 15 April 2010 - 07:05 PM Zach Kemppel New Member Member 1 posts I had this error, and this is how i fixed it. In these cases, the user must manually resolve the configuration problem. Verify that a power connection is also connected to the back of the floppy drive.

Jump to content FacebookTwitter Geeks to Go Forum Operating Systems Windows XP, 2000, 2003, NT Welcome to Geeks to Go - Register now for FREE Geeks To Go is a helpful When I go to F2 nothing happens or F12 nothing hppens, same message w/no results. This error can be caused by not having a diskette in the floppy drive(s) when you try to access it. Load default settings in setup. 3.

Advanced Search Forum PressF1 Floppy Disk Error at Startup How fast is your internet? If you encounter configuration (or setup) errors, refer to the installation instructions found in the new component's installation/user documentation. I was told by a computer shop that my hard drive needs to be replaced. I followed your steps and it worked accuratedly.

System board. 164 1. At Startup press "F2" to enter setup; Arrow down to select "Boot device configuration" - press enter; Arrow down to select "1st boot device" - press enter; Arrow cursor to select The error messages described in Table 3.1 are errors that occur and are reported before the single beep tone is produced at the end of the POST routines. Report harrispotter 2Posts Thursday May 13, 2010Registration date May 13, 2010 Last seen - May 13, 2010 11:42AM Your advice saved me.

I went to setup and disabled the floppy drive, even though I don't have one and now all is well Report guyver- Oct 3, 2009 06:17PM thats a bunch I dont Register now to gain access to all of our features, it's FREE and only takes one minute. The error code 40 is what I get during the boot up post process. Report lukefirewalker- Mar 29, 2009 10:59AM That did it, thanks.

Then it's off to the PC doctor! once again thanks and good luck ^_^ Report Warlock- Apr 12, 2010 07:41PM thanks man you know about computers Report NoRule- Apr 19, 2010 08:01PM skillz dat killz Report mathgeek- Apr Report David- Jan 8, 2009 03:51PM I have the same problem. SYSTEM HALTED, (CTRL- Indicates the present boot attempt has been aborted and the system must be rebooted.

The drive may be damaged. Secondary slave hard disk 3. If that still does not correct the error, try another floppy cable.Not ready reading drive AThis error may be caused by incorrect drive identification in CMOS. Report jeffhei724- Jun 10, 2010 01:08PM awsome had that problem and now its fixed thx Report the white knight- Jun 13, 2010 04:12PM Thank you so much I was having the

Why does this happen whenever my families computer starts up, and how can I fix it? You can check the BIOS setting by pressing Del or Esc when the computer starts up. Error Code 31 ? - Error Code.. Home > Articles Hardware Troubleshooting Techniques By Charles J.

by dhuber · 8 years ago In reply to You say One floppy and 2 optical drives. Any other ideas are welcome! 0Votes Share Flag Collapse - Follow these steps by Jacky Howe · 8 years ago In reply to All of the above ? :( It could Anmelden 11 Wird geladen... Your advice to someone else was: "I had the same bother and it was enabling floppy disc drive which I dont have.go to bios f2 and click on load default then

should not have anything in there enless you have floppy drive...... Any help would be appreciated. Power up the system, and try to boot to a floppy diskette and format a floppy diskette as mentioned on the previously. Thanks.

I then changed the setting for the a: floppy drive to "disabled" as I do not have one installed. Be sure the correct hard drive type is selected in Setup. The above picture illustrates what drive should be connected where. StevieD 3 April 2008 13:51:25 Ditto Change the setting in the BIOS.

Report doeboy- Oct 6, 2009 06:22PM went through the bios and didnt c anything that said , standard cmos, im pretty good with pcs and iv seen that b4 but I I then checked the system event log on the bottom. on the Floppy Drive you have the Cable on the wrong way. Replace the floppy if the floppy data cable did not resolve your issues.

Thnx again! See the Step 005 of 'Memory' to replace memory module. 3. Then reboot the system. Report Postal268- Mar 20, 2009 08:24AM Dude thank you so much, I had been messing with the setup for hours.

Im still not sure what the reason for the error is, because the floppy drive works fine. Verify that the floppy cable coming from the motherboard is connected to the back of the floppy drive. I so appreciate your information. Hard Disk(s) Diagnosis failure 2.

Arrow down to select "Integrated peripherals" - press enter; Arrow down to select "Onboard FDC controller" - press enter; Arrow cursor to select "disabled" - press enter; Press F10 to save RAM PARITY ERROR - Indicates a parity error in Random Access Memory. Thank you. In CMOS use the arrow key to highlight Standard CMOS Setup and press [ENTER].

If the floppy drive is not setup properly you may experience read/write errors or the floppy may not work at all. any help will be greatly appreciated Report cc21- Apr 23, 2010 02:28AM mathgeek, Back up you data and re-install your OS. Press and hold down the CTRL and ALT keys and press DEL. Thanks in advance for any advice Report jUNIOR- Mar 6, 2010 09:21PM THANKS A MILLION! :) Helpful +10 Report rapture Feb 2, 2009 02:04AM nevermind.