ge oven fo error Waucoma Iowa

Address Po Box 20, Ossian, IA 52161
Phone (563) 532-3232
Website Link
Hours

ge oven fo error Waucoma, Iowa

Any ideas on what might be going on would be much appreaciated. If I want a jet engine, I buy Pratt Whitney." Back To Top PM Quote Reply Current time is 02:40 am - > Do-It-Yourself Appliance Repair Help > The In the end, it cost about $300 in parts to replace the clock and the touchpad. In the morning all 10/15/2016 10/15/2016 smitty1486 Trying to figure out what the likely underlying problem for 10/15/2016 10/15/2016 smitty1486 Whirlpool gi7fvcxwa..

By reading any content on this site you agree to AppliancePartsPros.com , Inc. I normally recommend that you have a service technician repair this type of problem. LINK > GE J2B915SEH1SS Electronic Control LINK > J2B915SEH1SS Control Panel and Keypad Being as you say it only occurs while heating, that test may not be able to be performed I’m getting the error code F0 ( or FO) Online research tells me it has something to do with the controller for the oven… the top “burners” work fine.

Range.... Everything said control board and or touch pad. www.Appliance411.com The Appliance Information Site =D~~~~~~ Reply With Quote 06-22-2009,09:25 AM #3 sjalter New Member Join Date Jun 2009 Posts 3 Thanks 0 Thanked 0 Times in 0 Posts Dan O, You can try power cycling the oven or trying a different function before you start replacing parts.Then I'll feel less bad calling for service knowing I'm not paying two hundred dollars

Shut off power to the oven, disconnect the flat ribbon connector from the electronic oven control board and then restore electrical power. First you need to check the sensor, disconnect power, pull the range or oven out then take off the back cover. Once off, you should see the two small wires that are from the sensor disconnect them (some have a plug but if you have to cut the wires). If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.

Reply With Quote « Previous Thread | Next Thread » Thread Information Users Browsing this Thread There are currently 1 users browsing this thread. (0 members and 1 guests) Bookmarks Bookmarks This is often caused by a bad control keypad but it can sometimes be caused by a failed electronic control board in the oven console. Since the appliance was electrical I was a little leary so I called a repair man and since my husband was at home I left for work. Any suggestions?

I took several pics with a digital camera to help remember the connections. Note that this test should be done while the oven is at room temperature. You need both the touch pad and the controller replaced. Wird geladen...

F1 Failed transistor in control if you get this code the control board needs replacing. Now you should see a ribbon that connects the keypad to the control board and disconnect it. Maybe he had his fill of GE appliances. If within that day the code comes back, replace control if the code doesn’t come back, replace keypad.

Will help me figure this problem for you Ask Your Own Appliance Question Customer: replied4 years ago. Thanks again for your time and effort explaining the possibilities. This will explain Last edited on Mon Dec 12th, 2005 03:49 am by Jedi Appliance Guy Back To Top PM Quote Reply Posted: Mon Dec 12th, 2005 07:08 pm PM If the oven temperature sensor and wire harness are okay, replace the electronic oven control board.

It should be somewhere between 1050 and 1150 ohms. Service rep says they are all like that. Wähle deine Sprache aus. Considering it's both parts, which look to total around $300.00, do you think I am better off having a repair service do this work instead, and if so, any guestimate on

my oven beeps and the code is FO Report This by Manage My Life June 1st, 2010 model 911.47082100 kenmore 30 inch wall oven. Wird verarbeitet... When it stopped working, the display would change from the clock to a 0:00 lower oven timer reading with an audible beep. Return From Fault Code Guide Appliance-repair-it.com is a free service but it cost to keep it up and running.

A test that can sometimes be used to isolate whether the keypad or control is responsible is to disconnect one from the other to see if the error returned. the read out says FO. We have 10/15/2016 10/15/2016 woody463 Bosch 43 leaves dishes with scum or coating that looks like 10/15/2016 10/15/2016 JACUSTOMER-x0uwnnmp- X Ask an Appliance Technician Get a Professional Answer. 100% Satisfaction Guaranteed. JMO Dan O.

Any helpful hints on how to remove the top, then remove the font panel? Start Here Please enter part or model number: Help Finding Model Number Your Host Appliance Repair Expert Shawn Appliance repair since 1996 2-years refrigeration courses1-year electric theory courses1-year residential wiring course Category:Appliance Share this conversation Expert: Mike replied4 years ago. That could be the wiring or the sensor or the control board.Sensors are cheaper than control boards.F5 is the GE oven fault code for a failure in the control board.

I have annother ERC board but I don't want to install it if there could be another problem that needs to be fixed first or if in fact I received two Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs If code recurs, problem is in the control. Problem is allot of wires will need to be disconnected and then you would need to remember how to put everything back together (not an easy thing to do if you If you don’t find any loose connections, I would recommend changing the sensor even if it checks good cause it could be intermitting.

On some models, the keypad and the control board are made together, if so replace control. Wird geladen...