frigidaire wall oven error code f10 Sloan Iowa

Address 3200 Line Dr, Sioux City, IA 51106
Phone (712) 277-4555
Website Link http://www.marconet.com
Hours

frigidaire wall oven error code f10 Sloan, Iowa

We just had a something similar to what happened to Len yesterday. thanks josh Gene // Apr 10, 2014 at 5:03 pm Hello Josh. Jeff // Jul 17, 2015 at 2:59 pm Hi i'm having a problem with my Frigidaire oven professional series model number PLES389ECH I've followed your assessment steps with the following findings The part number for the EOC is 318183602 Gene.

Also the broiler coil came on but the unit was not in broil but bake. The part number for the EOC is 316562003 The part is on back order. Copyright © 2000-2016 ApplianceAid.com. The overlay is self adhesive.

F11 Shorted key: a key has been detected as pressed ( for a long period ) will be considered a shorted key alarm and will terminate all cooking activity. Otherwise the relay board is the culprit. As soon as you remove the rear panel the board should be visible. This error code means it was detected a shorted key on the keypad.

You can order it at www.repairclinic.com. It was the larger ribbon connector on the right. Select Model Number Part Number Enter your model or part number Search Can't locate your model number? What was wrong with the old one?

There is a separate membrane switch in your range which would need to be replaced in such situation. Measure the resistance between these wires. F30 Open RTD sensor probe or wiring problem. Gene.

Gene. Or why this part keeps damaging. .thank you Gene // Mar 7, 2015 at 2:35 pm Hello Sergio. It is giving F11 error. Resolved Question: How do I turn off the beeping sound when my Frigidaire oven says an F10 error code?Thank you Submitted: 5 years ago.

Its on Frigidaire FEFL69HCA Gene // Nov 16, 2013 at 9:41 pm Hello Ron. They are identical. Keep me posted. Is it something that an amateur could easily do?

Codes flashing are F 7 and 20. Valerie Gene // Dec 19, 2014 at 11:42 am Hello Valerie, Sad story. Keep me posted. My wife was baking cookies at 350 and the stove tripped the breaker.

Thank you for your question. If fault returns upon power up, replace the EOC. If the problem persists, replace the EOC. Gene.

After several power-cycles with the same error, I came to your page. Specifically the orange wire on the connector adjacent to the only non square or rectangular black component on the board. If the potentiometer failed any of the tests, it would need to be replaced. Keep me posted.

If your probe measures 2500 ohms or higher, then a defective temperature sensor is causing this problem. Keep me posted. Gene. Also the model number you posted is incomplete.

Gene // Dec 28, 2014 at 2:41 pm Hello Ken, The only way you can do it is to disconnect the EOC. I would suggest to call Frigidaire for service. Gene // Jan 3, 2015 at 7:48 pm Hello Sharon, Sorry for the delay. it started to throw a f10 code after about 15min on bake and wont stop beeping until I unplug it..ive noticed the element will stay glowing red even when the oven

Gene // Apr 7, 2015 at 4:26 pm John, Per the model number you posted this is a simple overlay (piece of plastic) which does not have any ribbon cables connected Gene. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & If the sensor checks no continuity, an "OL" reading on this meter, it should also be replaced.

Do you have any other questions? Our oven flashed F10 and went into runaway temps. It has to be exchanged under the part warranty. Jim // Dec 8, 2014 at 1:00 pm Hi Gene.

Yes, the temperature sensor tests OK. i am adding the link below to help you with your question while you wait for your expert response. The potentiometer is the control for surface element. My range is possessed.