ford f 350 error codes Pilot Mound Iowa

Midland Computer Systems offers services to individuals and small business that aren’t large enough to have their own IT department.  We build and service computer systems of any kind (excluding apple products or servers).  Our prices and services make the choice to let us help you an easy one.

Why Choose Us?Midland Computer Systems is based in central Iowa.  For those located in central Iowa, we provide the fastest, headache-free service available. Computer Repair:Our computer repair policy is “If we don’t fix it, you don’t pay”.  It’s that simple.  There is a minimum service charge of one hour ($50) and you’ll be up and running, or you pay nothing.  Give us a call or e-mail and let us know how we can help.  We may be able to help you get things fixed over the phone, at no charge.  New Computer Systems:Our computer systems are build custom for you and your needs.  Why spend money on buying a pre-built system from someone like Dell.  Trying to choose a random configuration of parts that comes closest to fitting your needs can be a headache, and cause you to end up spending more than you need.  Let us help you pick the components you need based on your usage.  We also build all of your systems with future upgrades in mind.  This will save you a lot of money over time.  Systems such as Dell, make it very difficult to upgrade due to the format of their cases, and limited upgrade slots on their motherboards.

Address Boone, IA 50036
Phone (515) 441-9190
Website Link

ford f 350 error codes Pilot Mound, Iowa

WIRING OR PTS HYDROSYSTEM P0753 SSA, wiring, PCM SSA electrical failure SSA circuit fails to provide voltage drop across solenoid. Accessing diagnostic trouble codes. DISCLAIMER: I am not a mechanic. Increase in EPC pressure (harsh shifts).

performance Harness routing, charging circuit, sensor P0344 Camshaft position sensor ckt. Incorrect gear selection, depending on failure or mode and manual lever position. Increase in EPC pressure. Today 10:00 PM by wackyman9 21 DIY shower base Today 09:56 PM by wackyman9 1 White smoke while idling Today 09:53 PM by wackyman9 2 White smoke, no boost.

May flash TCIL. Incorrect gear selection depending on condition mode and manual lever position. WIRING OR TSS SENSOR P0720 OSS Insufficient input from output shaft speed sensor PCM detected a loss of OSS signal during operation. WIRING OR TSS SENSOR P0717 TSS Turbine shaft speed sensor signal intermittent PCM has detected an intermittent TSS signal.

The manufacturer's names or trademarks used herein are referenced solely for identification purposes and are not intended by to cause confusion as to source or sponsorship. PTS HYDROSYSTEM. intermittent Harness routing, charging ckt., sensor, int. P1740 TCC TCC malfunction Mechanical failure of the solenoid detected.

WIRING OR 4X4 SWITCH P1728 Trans Transmission slip error The PCM has detected an excessive amount of slippage during normal operation. Incorrect gear selection, depending on failure or mode and manual lever position. Intake Manifold Runner Control circuit fault P1519? In (D) position trans, stuck in D or manual 2.

MCU System To clear DTCs, turn ignition Off. TCC slippage/erratic or no torque converter clutch operation. WIRING OR SUPER SOLENOID P1747* P0962 EPC, wiring, PCM EPC solenoid circuit failure, shorted circuit or output driver Voltage through EPC solenoid is checked. Torque converter clutch will always be off, resulting in reduced fuel economy.

Tires Find the right tires for your car Insurance Get a free insurance quote -- (Full) -- (Classic) -- (Mobile) Contact Us |Advertise | PowerStrokeNation : Ford Harsh shifts, harsh torque converter clutch activation and harsh engagements. On all models, to exit Self test, turn ignition Off. Trailer Towing Other; Brakes, Electrical, Hitches, Weight Distribution & CDL Discussion Small Chassis Trucks Crossovers 2011 & Newer Explorer Explorer, Sport Trac, Mountaineer & Aviator Ranger & B-Series Escape & Escape

Continuous DTCs should now be erased. sensor circuit low input Grounded circuit, biased sensor, PCM P0198 Engine oil temp. Remove jumper wire and reconnect DTC. 6. voltage, charging sys., internal PCM failure P0563 System voltage high High sys., voltage, charging sys., internal PCM failure P0565 Cruise "On" signal malfunction Open or short circuit, switch failure, PCM failure

Defaults to (D) or D for all gear ranges. See Solenoid On/Off Chart. Wait about two seconds. 5. WIRING OR TSS SENSOR P0718 TSS Turbine shaft speed sensor signal noisy PCM has detected a noisy TSS signal.

WIRING OR ECT SENSOR P0122 P0123 P1120 TP TP concern PCM has detected an error that may cause a transmission concern. Torque converter clutch will always be off, resulting in reduced fuel economy. WWW.SUPERDUTYPSD.COM FORD SUPER DUTY 7.3L POWERSTROKE DIESEL Mods, Maintenance, Repair, and Information Home Page Home Write-Ups Part Numbers Maintenance Torque Values OBDII Codes Documents Other Links: Torque Calculator | Oil Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material).

Circuit open or shorted or PCM driver failure during on-board diagnostic. See Solenoid On/Off Chart. Check engine lamp Continuous Memory DTCs are separated from Key On Engine Off DTCs by a six second delay, a single half second flash, then another six second delay. WIRING OR DIGITAL TR SENSOR P1705 Digital TR Digital TR self test was not carried out in PARK or NEUTRAL Vehicle not in PARK or NEUTRAL during on-board diagnostic.

May flash TCIL. WIRING OR DIGITAL TR SENSOR P1704 Digital TR Digital TR circuit reading in between gear position during KOEO/KOER Digital TR sensor or shift cable incorrectly adjusted; or digital TR circuit failure. Incorrect gear depending on condition mode and manual lever position. WIRING OR TFT SENSOR P0740 TCC, wiring, PCM TCC electrical failure TCC circuit fails to provide voltage drop across solenoid.

Wrong commanded EPC pressure. PTS HYDROSYSTEM IF THERE IS LOTS OF DEBRIS IN PAN YOU WILL NEED PTS KIT AND PTS BILLET TORQUE CONVERTER P0741** TCC, internal components TCC slippage detected The PCM picked up Short circuit results in minimum EPC pressure (minimum capacity) and limits engine torque (alternate firm). PTS HYDROSYSTEM P0781** SSA or internal parts 1-2 shift error Engine rpm drop not detected when 1-2 shift was commanded by PCM.