ford cd 6006e error 3 Pisgah Iowa

Address 504 Walker St, Woodbine, IA 51579
Phone (712) 647-2003
Website Link

ford cd 6006e error 3 Pisgah, Iowa

PINPOINT TEST A : THE AUDIO UNIT IS INOPERATIVE - DOES NOT OPERATE CORRECTLY TEST CONDITIONS DETAILS/RESULTS/ACTIONS A1: CHECK FOR VOLTAGE TO AUDIO UNIT 1 Disconnect Audio Unit C443 or C446. Thanks for the advice - it helped me wonderfully Martin September 2006 Had the same problem but managed to fix it by taking the top off and manually removing the How can I fix it without spending much cash ? Alun P. PINPOINT TEST B : POOR RECEPTION TEST CONDITIONS DETAILS/RESULTS/ACTIONS B1: CHECK THE ANTENNA CABLE SHIELD 1 Ignition switch in position 0. 2 Ignition switch in position 0. 3 Disconnect Antenna Cable.

E14 Overtemp Error The Audio unit is too hot, unit will not work until it has cooled down. Component Test CD Changer Harness NOTE:Refer to Wiring Diagrams Section 415-01, for schematic and connector information. Maybe not. When I press LOAD it says 'WAIT' for about 30 seconds and then says 'CD ERROR E3'.

THEN if it goes wrong I'll pay Ford to fix it. Any idea... B2: CHECK THE ANTENNA CENTER CONDUCTOR FOR OPEN 1 Remove the antenna mast.

2 Measure the resistance of the center conductor between the ends of the antenna cable. the subwoofer amplifier C990 pin 8, circuit 2-MD23 (GY/BK), harness side and the audio unit C447 pin 14, circuit 2-MD23 (GY/BK), harness side.

Then I withdrew the unit. If worse came to worse then there's always eBay for second-hand units if your unit is beyond repair - anythings cheaper then your friendly ford workshop! Hochgeladen am 26.12.2009Here are a few common problems that can cause error code 3. Your answer: (Add your answer here.

I had to manually remove the top CD (carefully!!) once the laser head was parked. No REPAIR circuit 91-MD15 (BK/GN) or 91-MD34 (BK/YE). Better than heart radio at least!!! I've ordered DIN keys to withdraw the stereo from my dash and as it's out of warranty will attempt this one all by myself.

A little manual 'assistance' ejecting CD3 and everything was OK. Cheers Rob [color:Blue]MK 3 TDCI 130 LX[/color] Stardust Silver Clear Side Repeaters Fitted Back to top #2 zedex82 zedex82 Little Megger Members 23 posts Posted 30 July 2005 - 07:59 PM TEST the system for normal operation. Search for a fix How can I fix myIn-Car CD/Radio?

So it seems they have all fallen out of their trays and now the laser arm won't go home and i have no way now of getting the rest of them Search Can I repair the switch on my vacuum cleaner? Add your question How can I fix my Nissan Almera Tino? I have had the exact same problem.

STEVE GOOCH January 2009 REGARDS THIS COMMENT. REFER to: Antenna Cable - LHD (415-02 Antenna, Removal and Installation) / Antenna Cable - RHD (415-02 Antenna, Removal and Installation). PINPOINT TEST G : THE RADIO REMOTE CONTROL IS INOPERATIVE TEST CONDITIONS DETAILS/RESULTS/ACTIONS G1: CHECK THE AUDIO UNIT OPERATES CORRECTLY WITHOUT USING THE REMOTE CONTROL 1 Disconnect Radio Remote Control C437. Free repair advice and information.

Last edited by Cossy Mike; 16-09-2011 at 08:05 PM. does not endorse any of the information supplied on this website by users. Anmelden 32 2 Dieses Video gefällt dir nicht? No sound from all of the speakers * Speaker(s). * Circuit. * Audio unit. * GO to Pinpoint Test D.

Not a usual fix but it worked for me :) :) Woo - Hoo - I fixed it March 2010 I had the same problem - focus 03 - and

Chat live - Instant help :: home :: add a question :: search :: help :: most recent :: unanswered Search: Go Fixed for free! In the manual it says this CD player should take 6 CDs, but since we have had the car it has only taken 5 CDs, so maybe this has happened befor TEST the system for normal operation.

The bad news is it cost me £175 to get it fixed, but bearing in mind its a £500 stereo I reluctantly paid it. REFER to: Audio Unit (415-01 Audio Unit, Removal and Installation). If the concern persists, INSTALL a new audio unit. We have a procedure we can do but if that don't work we'll 'ave to send it back guv'nor.

I powered it with a 12V power supply on my kitchen table and watched the mechanism through the holes in the top. C2: CHECK SPEAKER INPUT FOR SHORT TO GROUND 1 Disconnect Audio Unit C443.

2 Measure the resistance between the affected speaker connector pin 1, harness side and ground. REFER to the Component Test in this section. Learn more You're viewing YouTube in German.

Yes GO to C2.