fanuc power supply error codes Hettick Illinois

Address 909 Broadway Ste B, Carlinville, IL 62626
Phone (217) 854-6260
Website Link http://www.illinitechs.com
Hours

fanuc power supply error codes Hettick, Illinois

He was wondering what the different codes stood for, so we wanted to go ahead and list the different alarm codes for this series. Diff. We do not offer the advice that an on site Fanuc trained maintenance engineer can. Check the parameter setting and input signal.

This alarm occurs if an abnormally high current flows in the L-axis motor. Identify the Servo Component and Win!Jade York on Choosing the Right Encoder Copyright 2015 หน้าแรก บริการ ผลงาน บทความ FANUC ติดต่อเรา เวบบอรด EditRegion7 EditRegion8 EditRegion9 Fanuc Alpha Power Supply ER-19 When orientation by a magnetic sensor is specified, another mode (Cs contouring control, servo mode,or spindle synchronization control) is specified. Manufacturers Other Resources Servo Drives Servo Motors The RZ Team Uncategorized Connect with Us!

We do not offer the advice that an on site Fanuc trained maintenance engineer can. If you have need of a repair please contact us Name(required) Email(required) Company Comment(required) Leave a comment Fault Finding On Fanuc Alpha Spindle AmplifierModules July 9, 2015July 14, 2016 fanucrepairs Fanuc Check the parameter setting. BUT, Alarm still is on display.

Then check the front of the unit looking at its 2 digit 7-bit displays which should indicate an alarm number / code. Check the sequence. ER-08 When a servo mode control command (rigid tapping, Cs axis control, etc.) is entered, neither SFR (normal rotation command) nor SRV (reverse rotation command) is entered. ER-23 When bit 5 of parameter No. 4014 is set to 0 to specify that the slave operation function is not used, SLV (slave operation command) is entered.

All Rights Reserved. Part III describes the cautions that should be observed in switching fromthe C series servo amplifier to the α  series servo amplifier unit SVU or SVUC.This document uses the abbreviations listed Remedy Change setting from 200V to 230V. The PSU alarm is the most likely cause of the faultPaired alarms PSU Alarm 1 : Spindle Alarm 30 : Overcurrent PSU Alarm 2 : Spindle Alarm 59 : Cooling Fan

A06B-6087-H130 alarm codes Post navigation ← Software for Programming Modicon Quantum PLCs Restoring Fanuc Beta Drive Parameters → 2 thoughts on “Fanuc Power Supply Alarm Codes - Alpha Series” Alarm Code Description 1 Overcurrent flowed into the input of the main circuit. 2 A cooling fan for the control circuit has stopped. 3 The temperature of the main circuit heat To enter another mode, first cancel the Cs contouring control command. Alarm 09 (AL-09) Heat sink is overheated Causes Cooling fan is defective, overload, dust and dirty.

Components are from the base and the A20B-1001-0120 Top Card The components were replaced and the base and the top card checked. If you meg the motor and the cable and they are good, then it is probably out of spec components on your drive and it will have to be repaired. The "X"s after the H will be numbers, so an example part number is A06B-6087-H130. The alarms help us identify if you have a fault with the top card, whole drive (or base)  or elsewhere like the fanuc spindle motor Alarm 01 (AL-01) Motor Overheat Causes

Check the parameter setting enabling the use of the orientation function. When orientation is specified, do not specify another mode. AL02: A cooling fan for the control circuit has stopped. In order to submit a comment to this post, please write this code along with your comment: d97ab699e016995f4bdce00e1615c12a Like the Blog?

Check the parameter setting and the differential speed mode command. Check INCMD (incremental command). ER-07 When the Cs contouring control command is entered, neither SFR (normal rotation command) nor SRV (reverse rotation command) is entered. Generated Sat, 15 Oct 2016 15:07:15 GMT by s_ac15 (squid/3.5.20)

for Fanuc Parts Call:Telephone+1-434-971-1394 (EST)+1-619-477-9011 (PST)Fanuc Parts & CNC PartsFanuc Alpha Module Fanuc Drives Fanuc Control Fanuc Motor Fanuc Monitor Fanuc Power Supply Unit CNC Monitors CNC Manufacturers Newsletter Email address: ER-20 When bit 5 of parameter No. 4014 is set to 1 to specify use of the slave operation function, bit 5 of parameter No. 4001 is set to 1 to Videos Documents Product database for the manufacturing industry Product database - Overview Product categories Machine tools Welding and cutting machines Parts and components Precision Tools and Clamping technology Electrical and electronic To enter another mode, first cancel the spindle synchronization control command.

On power up the green PIL led will light, the 7 segment display will display the software revision (ie A/00/15) followed by a flashing "-" Once the Fanuc CNC has made Check the parameter setting and input signal. ER-21 In a position control mode (servo mode, orientation, etc.), SLV (slave operation command) is entered. Check the parameters settings.

The system returned: (22) Invalid argument The remote host or network may be down. ER-11 When a servo mode control command (rigid tapping, Cs axis control, etc.) is entered, another mode (such as Cs contouring control, spindle synchronization control, and orientation) is specified. The time now is 02:45 PM. ER-02 When the spindle and Fanuc AC Motor are specified separately (with bit 5 of parameter No. 4001 set to 1, and bit 6 of parameter No. 4001 set to 0)

AL01: The main circuit power module (IPM) has detected am Error (PSM-5.5,-11) Overcurrent flows into the input of the main circuit (PSM-15 to –30). More ... ER-18 When bit 2 of parameter No. 4001 is set to 0 to specify that a position coder signal is not used, orientation by a position coder is specified.