fl01 error hot tub North Metro Georgia

Address 600 Old Johnson Rd, Lawrenceville, GA 30045
Phone (770) 653-5135
Website Link http://alltechguys.com
Hours

fl01 error hot tub North Metro, Georgia

Pump may also be deactivated). ICE = Freeze protection. Any assistance would be helpful. If the red light comes on use your multimeter to check for 240vac at test points J9 and J10 on your PWA.

Tested heater, t-stat, set a call & unit responded. The filter/circulation may also be deactivated). Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi Hot Tubs & Spas is headquartered in Chino, California. Something mechanical is obstructing the flow of your hot tub water.

OHH = Overheat. FL1 error was gone. Ideas?? - thanks, chip Nigel June 23, 2016 Reply Chip with the pump on test the psi switch with your multimeter set for ohms. Sometimes sets code sometimes not.

Spa is shut down. Both filters have been cleaned in a tub overnight with FilterBrite. You may have left this message years ago, I am not sure. Program setting of spa unit for Economy Mode.3.

Email check failed, please try again Sorry, your blog cannot share posts by email. %d bloggers like this: Login|Contact Us Pool and Spa Questions about Pool Repair? Emergency Shutdown The system has detected that spa water temperatures are above acceptable safety limits. As I said, there is no voltage arriving on TB4. And where would it be located.Just trying to see if there is anything I can do as to avoid the $60(cdn) trip charge if still under warranty.Any help would be greatly

The J- 385 features four deep bucket seats. Manual is very vague on fixing problem. No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. HLoH = Hi Limit Over Heat.

Nigel June 20, 2016 Reply Dave if you have activated a heat call and you have no voltage at the circ pump assignment contacts and you have an FL1 you may Add water if needed.2. Purchase new UV bulb from dealer and reset countdown timer. ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement

OH = High temperature condition, has reached 110ºF. Contact qualified service technician. Thanks Nigel January 30, 2016 Reply Nathan, check for voltage at your circ pump connections on your PWA. Husband will check the pump for an air bubble - have also found our local distributor in NZ does not ring back so is even more frustrating March 09, 2014 Reply

The final problem could be the pressure switch/flow switch itself. Nigel June 01, 2016 Reply Joe if you have your spa in Standard mode, you have made a heat call and you have no voltage at your Circ point assignments you In the first 4 years we basically used one filter and never got this error message. If the connections are good I would start with the Temperature sensor Shelley.

Temp has crept up from 88 to 93, but not from heater, thermal transfer I guess. DO NOT GET INTO THE WATER. Contact the dealer or service technician. BLB (Flashes in between water temperature and “blb”) Indicates that spa needs a new UV bulb.

Wait three seconds and then restart the spa to see if error clears up. Filter and circulation pump is activated and the heater is deactivated DO NOT GET INTO THE WATER. If so you may want to replace? Ecn = Spa operating in Economy Mode.

NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor. It has been an off-and-on problem recently, according to the former owners of the house. System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps. The initial code was an FL1 and we realized it didn't have enough water in it.

Sometimes will work correctly on all speeds, sometimes low only, sometimes when going from low to high it will immediately cut out.