frigidaire range f30 error code Sheridan Lake Colorado

Address 7245 US Highway 50, Lamar, CO 81052
Phone (719) 688-2717
Website Link http://www.pcmediageek.com
Hours

frigidaire range f30 error code Sheridan Lake, Colorado

unplugged it overnight and it worked for about a week and a half and last night at 2am it came back. The potentiometer is the control for surface element. ft. ... The range is beeping with the error code F11.

Pull the range out of the wall and unplug it. At Sears, they cost $7.58 and $28.03 respectively. Just in case you will decide to get new control panel, the part number for the control panel is 316538405 Good luck. In this range there are no a separate keypad.

You may want to start the troubleshooting from testing the temperature probe resistance. The t/stat you need to reset looks just like the one on the back. I was 10/3/2016 10/3/2016 JACUSTOMER-x0uwnnmp- We have a GE Profile Spectra convection oven, which we have 10/2/2016 10/2/2016 JACUSTOMER-x0uwnnmp- I have a Jenn-air Duel Fuel PRD 3630. I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top.

Check the upper oven temperature sensor by measuring resistance between two wires connected to the pin 9 and 10 at the plug P27. or Is it something else that's causing this problem? Please verify it. Gene.

Thank you for your question. When we were changing out the EOC one of the ribbon connectors (that connects the EOC to the TST control panel) pulled apart. LOL) Gene // Dec 24, 2014 at 12:11 am Hello Len, This error code means the microprocessor has found the lock motor switches to be out of sequence or shorted. If the potentiometer failed any of the tests, it would need to be replaced.

Ken // Dec 24, 2014 at 4:00 pm Gene, Merry Christmas. Gene // Apr 26, 2015 at 5:28 pm Hello Dirk, I'm afraid, while you have been washing the stove, some of cleaning liquid leaked inside the control panel and caused electric Click here to visit Merchant's home page. I'm confused about the difference between #219 and #219A, though.

I checked the RTD probe out and it reads okay (1080 or so). Steve // Mar 29, 2015 at 8:13 pm Hi, I have a frigidaire oven Model #FES355EBA , I am getting the F10 error only when oven is on, does not error If all above fails to correct the situation, replace the EOC in the event of a motor that does not rotate. If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe).

We'll help you figure it out! The one in question is black colored. Neil // Apr 4, 2015 at 11:09 am Hi Gene, I have read through all of the postings on this page however I am unable to figure out the issue with The part number is WB2X9998 Good luck and keep us posted.

Check RTD resistance at room temperature ( compare to probe resistance chart ). The part number for the EOC is 316557205 The part number for the overlay is 316419303 Good luck and keep us posted. Thanks for your help Gene // Apr 23, 2015 at 10:12 pm Hello Jeff. This may have just solved your error code!

If the reading is incorrect, remove the sensor from the oven and check its resistance at the sensor. When replacing a potentiometer, do not over-tighten the hex nut. Pull it out of the wall and remove the control panel rear cover. Actually it is always the safest way.

The correction for this problem is to replace the EOC. My wife is suspicious of the temperature, however. creeps up about 20-50 degrees over the setpoint; but the display still shows the correct temp. Thanks again!

Shop HalloweenCostumes.com for Suicide Squad costumes and accessories. Contact the seller and request the replacement. Any suggestions? I found them for you: "Each oven temperature can be individually adjusted.

disclaimer and Terms of Use. To test operation of the potentiometer m View Cart| Contact Us| Track Order| Customer Service| My Account Discuss error code f30in Oven Repair (including Ranges and Cooktops). "I had the Or sign in with one of these services Sign in with Microsoft Sign in with Twitter Sign in with LinkedIn Sign Up Blog Entries All Content This Blog Entry This Blog Reply With Quote Quick Navigation Frigidaire/Tappan/Electrolux Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Announcements Membership Testimonials Website Forum Issues/Problems Model Number Location Help Appliance

Its on Frigidaire FEFL69HCA Gene // Nov 16, 2013 at 9:41 pm Hello Ron. The display should be blank. FGGF3076KBK. Keep me posted.

The correction for this problem is to replace the EOC. F30 Open RTD sensor probe or wiring problem. My range is possessed. Ask Anonymously Popular Products GE Profile Spectra JGBP90 Gas Kitchen Range 3 Questions Maytag MER6772 Gemini Electric Kitchen Range 0 Questions Kenmore 79012 / 79014 / 79019 Gas Kitchen Range 2

However, a quick glance at page 12 of the Factory Parts Catalog's wiring diagram (Frigidaire PLES389ECH - YouserGuide or http://www.serviexcell.com.mx/manuales/PLES389ECH.pdf) shows two thermal breakers wired into the circuit as well. Hi gene- I have a runnaway temp issue. Gene // Mar 17, 2015 at 11:08 pm Hello Billy, Thank you for your question. You can either ...

Keep me posted. Follow the violet wires that are coming off the oven sensor connection. We bit the bullet and bought the EOC, I installed it….and have had no change in operation :(. If the oven problem is intermittent you must do the tests when the oven is malfunctioning.

Gene // Mar 18, 2015 at 12:17 am Hello Crystal, Thank you for your question. In this model the keypad is a part of the EOC. Gene // Jun 18, 2015 at 4:49 pm Hello Connie. Replaced temp probe and same thing.