fix the e 74 error New Raymer Colorado

Address 1215 Edison St, Brush, CO 80723
Phone (970) 842-9980
Website Link http://thebrushgeek.com
Hours

fix the e 74 error New Raymer, Colorado

The guy said that the "promotion" had expired in February, but when he pulled up my account, it says that I am still within warranty. Step 2 Applying the FixThese pennies are going to be made into heat conductors and absorbers. When you boot up your xbox with the paper clips in it you will wait about ten minutes or until the single red ring turns into to red rings. Anyone know what this means or how to fix it?

Wird geladen... for about 5 days. There isn't a spec of dust in that beast :p haha. At work I use Hakko desoldering gun but at home I have a Radio Shack desolering iron and it works fine for home use.

I don't think you have any other option other than to call for the coffin. Anmelden Transkript Statistik 64.179 Aufrufe 164 Dieses Video gefällt dir? The best part? Before getting the board ready to reflow remove the two caps near the HANA chip they are too close to being in the way to try to shield.

Good Luck, Cody Guide Reflowing Xbox 360 Motherboard Difficulty: Difficult Was this answer helpful? If you have the RRoD error, you can put your Xbox back together (more than likely). Sign up for free! Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt.

We won't give up and neither should you. Mostly it is one of the outer solder balls on the side facing the (H)ANA chip so a shim increases the chanced of success quite a bit. It is similar to any other willful overheating and may work for a short time. Shipping is included and they come to your door.

Diese Funktion ist zurzeit nicht verfügbar. Reply 1 gidoon crap 7 years ago hay man i did that and its not working i have one ring of dead and it is the same as your and it Fix and Prevent E74To fix the E74 error, we need to apply pressure to the HANA/ANA chip. Wähle deine Sprache aus.

Gears of War 3!!! Wipe the dust off it occasionally. mannyfre5h117 on 2011-04-16 01:24:45 : guys i fixed my e74 with just replacing the xclamp with m5 screws with washers(zinc,plastic) it works fine, but now i realized that in certain games Fix and Prevent RRoDWrap 4 sets of 2 pennies each in electrical tape.Apply a thin layer of thermal paste to the black RAM chips where the old pads were.Now, put the

View the answer I have this problem too Subscribed to new answers Is this a good question? The risk that one runs is to destroy the logic board and other components through overheating. Note The warranty period for the E74 error is three years from the original purchase date of the console. Go to EB or something and get new ones.

I would not worry about doing the X-clamp fix, since your problem is not with the GPU or the CPU. Wird geladen... About 20 minutes of running the Xbox should fix it permanently. Preview my answer Post my answer View Statistics: Past 24 Hours: 25 Past 7 Days: 192 Past 30 Days: 883 All Time: 118,050 22,225 Free Manuals 86,965 Solutions 6,447 Devices iFixit

Just keep it standing, and off the carpet.. We need to strip everything, including heatsinks. Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. I just called xbox support to complain to them because I found articles all over the web that any console manufactured before January 1st 2006 was eligible for a free "out of

Learn more You're viewing YouTube in German. Featured Story: How to Post to Null Byte [4.10.15 Revision] Null Byte: The aspiring white-hat hacker/security awareness playground — WonderHowTo How To: Fix Your Overheating, RRoD, or E74 Xbox 360 with My xbox actually started flashing 2 red lights after this :-( 11/26/2014 by Akisha Overheating is what's causing that, get a new fan for the thing! The RRoD is sometimes caused by excessive dust, but is more commonly caused by heat warping the GPU or CPU away from the motherboard.

BulovaMember Since: October 17, 2003Posts: 1237BulovaFollowForum Posts: 1237Followed by: 0Reviews: 0 Stacks: 0Forum Karma: 0#10 Posted by Bulova (1237 posts) - 9 years, 6 months agoTake your hard drive out and The pennies will put enough pressure on the HANA/ANA chip so the 360 runs. Or do I have to do 2 separate reflows: one focusing on the GPU and one focusing on the HANA? Answered Ask a Question To ask or answer questions, please log in or register for free.

slayer85Member Since: November 20, 2006Posts: 926slayer85FollowForum Posts: 926Followed by: 0Reviews: 0 Stacks: 0Forum Karma: 0#15 Posted by slayer85 (926 posts) - 9 years, 6 months ago i wonder if yo8u could Melde dich an, um unangemessene Inhalte zu melden. Du kannst diese Einstellung unten ändern. Dont call Microsoft so quickly.

They also prevent and reverse flexing in the motherboard because they are solid. For example, disconnect all Xbox 360 controllers, all Xbox 360 Memory Units, and the Xbox 360 Hard Drive. 3. Call microsoft. It helped mine!

i dont know how much it would cost of if they would even do it, but i dunno, just throwing an idea out BulovaMember Since: October 17, 2003Posts: 1237BulovaFollowForum Posts: 1237Followed rrod because you can over heat it and fry it so un can get it replaced free k2theswissMember Since: November 20, 2007Posts: 16599k2theswissFollowForum Posts: 16599Followed by: 0Reviews: 5 Stacks: 1Forum Karma: This was the 1st time I tried it and was by accident (using it for power while flashing a drive) but I will just save for a reball in future! Make another stack of pennies that can go under the white heat duct, enough so that it pushes the duct up a noticeable amount.Place the duct and DVD drive back in

Wird geladen... Right from the start, the console has suffered a multitude of different hardware failures and design flaws. onthemark11 on 2011-10-19 06:01:24 : I have a legit rework station. No BS.

Then I've bought cables I can't return BulovaMember Since: October 17, 2003Posts: 1237BulovaFollowForum Posts: 1237Followed by: 0Reviews: 0 Stacks: 0Forum Karma: 0#7 Posted by Bulova (1237 posts) - 9 years, 6 If you don't want to wait for a month, you can also fix E74 problem with the help of this DIY Video, the guide will explain step by step approach to E74 again...