f11 error code on kenmore washer Fort Morgan Colorado

Address 25265 County Road T5, Brush, CO 80723
Phone (719) 649-3739
Website Link
Hours

f11 error code on kenmore washer Fort Morgan, Colorado

Undo dross In what way can a wiring harness go bad? For those who dont have a technician available to them, any local electronics repair house could do this for you. Instead, i folded a couple dish cloths and put one under each foot of the washing machine. Yes No Voted Undo Score 8 Cancel Comments: THIS WAS THE SOLUTION to my problem!

You mean there is a transmission between the engine and the tires? He (the repairman) changed a motor on the pumb but still got the same code. They looked clean......... Will keep all posted.

I'm not quite sure where you're saying it needs resoldering. I could get readings over 40╬ę during the bump. I had a load in the wash and the error code F11 came on and continued to flash and beep loudly. Not finding what you are looking for?

Thanks for the info. Do I release all of these and the control box drops down with the lid still attached to the metal? Since the outlet is AC, there really isn't any positive or negative to "cross polarize"- that's only in the DC world. Let us know more about your unique need and we'll provide an estimate for your custom repair.Get A Quote Contact Us Business Hours: M–F: 8:00am – 5:00pm ESTToll–Free: 800-547-2049Phone: 864-641-0564Fax: 877-799-2927

So, I did my parts research, identified the correct part number using the manufacturers website, then went other places to price the part. So I... Hopefully it helps you. Refer to the water temperature sensor section.

Bad thing is I'm not sure if it was the polishing, or just removing/reseating all of the connectors (probably never know). True to form, the washer immediately gave him the dreaded F11 and Fdl codes. Easiest way to check latch operation is via the diagnostic mode (complete directions in the tech sheet that can be found by removing the bottom panel, and it is packaged on First, UNPLUG THE WASHER.

We have the board out and know where the relays are, but when posts say "Heat up the contact point for each harness connection on the TOP AND BOTTOM OF BOARD While your underneath the board RESOLDER THE RELAY SOLDER POINTS FOR ALL THE RELAYS. Andrew Like Bookmark April 13, 2008 at 6:28PM Thank you for reporting this comment. [email protected] Like Bookmark May 13, 2007 at 10:15PM Thank you for reporting this comment.

Now 3 weeks later all is still working fine. There was only one minute left in the spin cycle so I tried to press the pause/cancel button in hopes to stop the cycle and unlock the door to get my For about four months, I have been getting an "F-11" error code at times during the wash cycle. Presumably you could test it for continuity on the leads, maybe add a bit of deOxit for better conductivity. $128 doesn't sound so terrible for a control board, but really appliance

I then cleaned the contacts with alcohol to remove any solder dust between the contacts. Since the CCU is right at the top, I would suggest this to verify the relays are the problem: get a cycle started and knock on the CCU while running; when Thanks to all for your help. 05/02/2015 by rajastrums Door locks, Machine puts in water, F-11 code goes off before drum turns. Found it...

I tried just doing a drain/spin and get the same error. Many different error codes plague these washers.We repair and upgrade the ROOT CAUSE of the defects. An Invite to all for info of what I had to do with our Duet at this link: http://www.flickr.com/photos/mysteryonionpatch/471156850/ Removed board, desoldered relays, clean the contact inside relay, switch places, resoldered, But the problem began occurring more frequently, to the point where every time the machine went into a high speed spin cycle F11 would interrupt.

To insure that this may be the problem, take a ride and sit on it during the final spin ;-) If it works then you know it's probably the wiring, if Has anyone else experienced this? After removing it, I popped the ECA cover open and saw nothing notable, except the disappointing fact that mechanical relays are involved. so i need a new unit and found it in stock here http://www.appliancepartspros.com/part_details.aspx?part_id=3881133 my machine info p/n ghw9460pw0 s/n csr380317 the people at appliance pros did a search with the info

Not being able to tell for sure I re-soldered it anyway. However, that did not stop F11 from happening. Good Luck. All rights reserved. © Applianceblog.com 2004 - 2014 SALE RUG SALE 0Sign In PHOTOSKitchenBathBedroomLivingDiningHome OfficeBaby & KidsEntryHallStaircaseExteriorOutdoorBasementGarage & ShedHome BarHome GymLaundryPoolStorage & ClosetsWine CellarView all photosFIND PROSArchitects & Building DesignersDesign-Build FirmsGeneral

The door locks, the water starts and then a few more seconds - F11. To our surprise it was quite easy, the first post explains clearly what to do. Step 2:Select All Error Codes That Apply: FDL F14 F06 F11 F35/SUDS F01 F28 No Code/No Spin F71 F01E02 (F1E2) F06E02 (F6E2) Step 3:Tell Us More About The F11 Error Code: Right relay throws nice arc when firing lock and unlock solenoids.

I followed his advice and added solder to all of the board contact locations and reassembled the machine. Does this fix the problem for good? Next the blue wire on the LHS of the CCU, last set (back) there are three blue wires.