fsck read 32 bytes at input/output error Smith River California

Repairs Home/Office Electronics Home/Office Appliances Home/Office Networks Home/Office Computers Support Home/Office Networks Home/Office Computers Cell Phones Websites Windows, XP, Vista,7,8,8.1,10 Android or IPhone Not listed, just ask. Tutoring Websites Computers Smart Phones

Address 1400 northcrest dr, Crescent City, CA 95531
Phone (707) 457-2125
Website Link http://crescenttechsite.wordpress.com
Hours

fsck read 32 bytes at input/output error Smith River, California

If I had to hazard a guess, I'd say that theres probably a whole slew of blocks around the same address which will report I/O errors (assuming the raid striping is Operating System: Boot files: /syslinux/syslinux.cfg /ldlinux.sys ============================ Drive/Partition Info: ============================= Drive: sda __________________________________________________ ___________________ Partition Boot Start Sector End Sector # of Sectors Id System Invalid MBR Signature found. Is there a way to find out. I am guessing the card is either damaged or a contra fit.

Here is the output of boot info script Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => No known boot loader is installed in the MBR Also check your dmesg for errors. What are Imperial officers wearing here? I'd also advise you to try it with a pc and card reader.

The integrity check of the ADV area failed. But for some reason I was not able to delete those files (0 bytes) from Windows 7 either. I found following link useful to understand 'debugs -R' output. It say the card is not supported.

Therefore the problem is the N900 and it's back cover. No need to even deal with SMART at this point. I do not run windows but ubuntu and i do not have a microsd slot on my computer. You may try using lsblk to see your disk device tree; that should help you to identify the USB disk drive by its device name.

The LBA addressing is an abstraction against the real disk underneath. Good Term For "Mild" Error (Software) Are there any rules or guidelines about designing a flag? Up-vote well framed questions that provide enough information to enable people provide answers. The buggy files were gone.

AlMehdi2010-08-04, 22:51try the umount command; and reboot i think its root, then umount /media/mmc1 reboot Thanks but have already tried that. Tango Icons Tango Desktop Project. Is Partition Magic 8 still the best? I can live without the data but it would be nice to get some back if possible.

Not the answer you're looking for? asked 4 years ago viewed 1503 times active 3 years ago Related 11Why can't I copy a large number of files to my USB flash drive?4USB flash drive mount issue3How do up vote 26 down vote favorite 13 I replaced a buggy Windows Vista installation with Ubuntu. UPDATE Doing further research I found that action related to problematic inodes (like above cp command) trigger following line in kernel log: kernel: cciss: cmd ffff810037e00000 has CHECK CONDITION sense key

In any case, you have a bad disk and you should look to replace it ASAP. Re: Input output error on read /dev/sda so you ran the boot info script and no joy? I have no problem with the back cover. but after some clicking i could start the format.

What should I look for? All works fine except that the main HD where I had all my files are now inaccessible. What specific server and controller firmware are you on? AlMehdi2010-08-04, 21:36I am pretty much lost on what to do.

What model server is this? Review paper/book on Finite Difference Methods for PDEs What sense of "hack" is involved in five hacks for using coffee filters? AlMehdi2010-08-04, 21:50No i hadn't so i tried it but did not work ;( geneven2010-08-04, 21:53No idea. Solution (steps for vmplayer, but could easily be followed for virtualbox): Add a new HD to your vm (had to start vmplayer as root) When prompted for the disk type choose

so i tried to install it again but got the error "INPUT OUTPUT ERROR ON READ /DEV/SDA" and installer is not detecting windows partitions I have 120G western digital wdc wd1200bevs-22rst0 but it does. EvenSt-ring C ode - g ol!f With the passing of Thai King Bhumibol, are there any customs/etiquette as a traveler I should be aware of? But as dd did not work it cannot be anything I did to try to rescue it that changed anything, as I did not do anything after running dd except updating

Assuming EOF. AlMehdi2010-08-06, 21:07I am not sure.. not that it helps.. And to see if there is actualy anything to mount: $ sudo fdisk -l /dev/sdb Disk /dev/sdb: 3951 MB, 3951034368 bytes 122 heads, 57 sectors/track, 1109 cylinders, total 7716864 sectors Units

Beware: what you need is not the disk sector number, but the partition- and filesystem-specific block number. share|improve this answer answered Jun 6 '15 at 21:13 Bleeding Fingers 3252518 I don't see an option to add a physical disk in VirtualBox. Did any Jedi question the ethics of having a clone army? I wrote what card it is in my OP.

share|improve this answer edited Aug 8 '14 at 19:35 answered Aug 1 '14 at 15:06 ewwhite 151k47298576 It doesn't seems ext problem, there are lowlevel disk read problems. –peterh If not, is there a way to repair the HD from Ubuntu? shadowjk2010-08-05, 23:30So if standard tools on a PC fail with the card, it's utter garbage. User contributions on this site are licensed under the Creative Commons Attribution Share Alike 4.0 International License.

share|improve this answer answered Aug 8 '14 at 19:18 Matthew Ife 16.8k23751 add a comment| up vote 3 down vote That's a lot to process...