frigidaire gallery f11 error Shasta California

Address Redding, CA 96002
Phone (530) 242-6972
Website Link
Hours

frigidaire gallery f11 error Shasta, California

Most likely the problem is a faulty EOC. Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to My manual and the internet are no help… Do you know what this means? Level and Position Range - When installed to the floor.

Sometimes it goes away for a few days, other times it comes back as soon as I turn it back on. Any thoughts at this point? Hi im an appliance tech and i had the same problem its not the EOC other words control board its actually the speed bake swith its stuck in the on position The cause of this error code can be a faulty door lock assembly or a faulty EOC.

Gene. what is a speed bake switch? The part number for the potentiometer is 316239605 The part number for the UIB is 316426400 Good luck. Inspect the overlay.

Gene // Dec 18, 2014 at 7:58 pm Hello Jim, Sorry for the delay. I did what you said and paid to have the circuit board overnighted and installed. self-clean - Use to set the keep warm - Use to start - Use to set broil feature. If any of the readings is incorrect (any resistance other than infinity), trace that wire and let me know where it goes to.

Wiedergabeliste Warteschlange __count__/__total__ My Frigidaire Oven goes Beep, Beep, Beep!!! The part number for the EOC is 316576604 and you can order the part by clicking on the part number. We've only had the range for 11 months. Thus the solution is to replace it.

Sounds like the EOC is the culprit. Is it something that an amateur could easily do? The temperature sensor part number 316217002 The relay board part number 316429800 This part is on back order. Good luck.

Today for the first time I lite a fire in? 6 answers More questions Outdoor faucet is breaking , need to replace? 7 answers How long do toilet water supply lines and other Appliance Specialists are ready to help you Ask your own question now Customer: replied6 years ago. ft. ... Then when we started removing the relay board we found out it was fried (black soot).

copper ground strap from factory with upturned ends. Du kannst diese Einstellung unten ändern. When I check the EOC it give a random number and goes back to OL on the tester. If the door lock motor never stops rotating, or if the F95 error comes back again, verify wiring of the motor.

I have spent lots of time researching my issue and can not find anyone else describing this particular problem. Check for continuity between the two probe wires. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. The burners work fine, oven cannot be used.

If the reading is incorrect, the temperature sensor would need to be replaced. Well, we followed your path, which was very helpful, but we have not solved our F11 problem. We bit the bullet and bought the EOC, I installed it….and have had no change in operation :(. You may want to replace it as well.

Need a Frigidaire FGEF3055KF manual? If the error code returns, the EOC would need to be replaced. It's worth a thousand words. The part number for the relay board is 316443925 Thank you for stopping by.

Ask Your Own Appliance Question Share this conversation Related Appliance Questions Question Date Submitted I have a LG THROMM model 2077CW electric clothes washer with 10/15/2016 10/15/2016 JACUSTOMER-x0uwnnmp- I have Kenmore Possible there is something wrong with the oven door hinges. With the diagnostics above, I was able to pretty quickly determine that the EOC was bad. a dual radiant element ...12 Setting keep warm ...23 Adjusting oven temperature...

I need some direction on where to look next. In the morning all 10/15/2016 10/15/2016 smitty1486 Trying to figure out what the likely underlying problem for 10/15/2016 10/15/2016 smitty1486 Whirlpool gi7fvcxwa.. Keep me posted please. The oven throws F30 regardless of whether the probe is attached.

You have to click on every one of them.