floppy error 40 Palos Verdes Peninsula California

Address 15721 Crenshaw Blvd, Gardena, CA 90249
Phone (424) 201-0212
Website Link http://www.pcscomputerworld.com
Hours

floppy error 40 Palos Verdes Peninsula, California

Another approach is to get a budget USB FDD (as made for legacy-free laptops), one that has Win98 driver provided. Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account? Transkript Das interaktive Transkript konnte nicht geladen werden. on the Floppy Drive you have the Cable on the wrong way.

KeithWindows ME (spare computer) Windows XP 2002 Professional SP3 (desktop computer) Windows 7 Professional SP1 32bit(laptop computer) Windows 8 64bit spare drive for laptop computer Back to top #15 hamluis hamluis We recommend you contact the computer manufacturer, have the computer serviced or that you replace the floppy drive then the motherboard if the issue persists. You can also set the floppy seek which as I understand it to be which floppy it reads on startup. Floppy Disk(s) Fail (40) (Problem Resolved) Started by andrewasmith1 , Jun 28 2005 12:47 PM Page 1 of 2 1 2 Next Please log in to reply #1 andrewasmith1 Posted 28

If it was then the connector is the wrong way around, I do know that much.I forgot to say I ordered a new 5 connector floppy cable (eBay) the same day LET OTHERS KNOW Tweet If you accept cookies from this site, you will only be shown this dialog once!You can press escape or click on the X to close this box. Turn the cable around 180 degrees and put it back onto the system board. A: = None.

i disable integrated LAN and no error halt 0 #12 bigbearvengeance Posted 06 March 2011 - 07:40 PM bigbearvengeance New Member Member 1 posts Back to the floppy disk (s) fail I even selected floppy seek because I occasionally boot up with a floppy whan I format and do a rebuild. In the beginning there was the command line. Anmelden 324 13 Dieses Video gefällt dir nicht?

Using the site is easy and fun. Once in SETUP you need to check that CMOS is identifying your Floppy Drive and that it is the correct one (i.e., 3.5 in., 1.44MB is the current standard for diskette Pin one is normally next to the drive motor on the Floppy Drive. Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

Jump

Edited by Platypus, 12 January 2009 - 07:40 AM. Thank you 0 #8 Zach Kemppel Posted 15 April 2010 - 07:05 PM Zach Kemppel New Member Member 1 posts I had this error, and this is how i fixed it. If it has become completely disconnected you will need to re-connect it. Wähle deine Sprache aus.

Are these drives new or used.This error generally means that the unit has died.Error code 31: ERROR_GEN_FAILURE - A device attached to the system is not functioning. 0Votes Share Flag Collapse The system's CMOS settings may be incorrect. Recently added New Hardware?If you have such as a tape backup unit, sound card, scanner, network card, etc. Some older BIOSes default to 5.25" drive and have to be manually set to 1.44M 3.5"This is a point I'm not too sure about the light flashing.

I have tried a new cable and nothing. My thought in asking if the access light gave a flash at power-up is that some PSUs have a FDD power connector that's easy to connect backwards & fry the drive. Conflict within the system with some newly added hardware or software. Power up the system, and try to boot to a floppy diskette and format a floppy diskette as mentioned on the previously.

Also check on the Motherboard to see if you have pin 1 on pin 1 if the connector is free standing. :) 0Votes Share Flag Collapse - Must not be the No it is not a Compaq but thanks for the information as I work on a lot of Compaq's and HP's. Several functions may not work. The one I use for my laptops was $29.95 at an office supplies chain store.

Top 5 things that never get done:1. Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. Social Sharing Find TechSpot on... Check the CMOS to make sure that the drive(s) are identified correctly.

If the issue persists, unfortunately it is likely that either the floppy drive is bad or the I/O board or Motherboard is bad. Power down the system and locate where the data cable is attached to the system board. Mar 25, 2006 Floppy Drive Error Feb 25, 2006 Floppy Drive Failed (40)????Help Jul 18, 2007 New Hard drive = no floppy? The current standard setup is:Drive A : 1.44, 3.5 in.Drive B : None (unless you have two Floppy Drives)Press [ESCAPE] to exit Standard CMOS setup.

I havent got floppy, and i had disable flopy in/on?? Thanks! By bumping on someone's topic it makes it confusing for the tech to understand who they are helping. Next to Fords, any computer is a piece of cake. (The cake, its not a lie) 3770K @4.5, Corsair H100, GTX780, 16gig Samsung, Obsidian 700 (yes there is a 700) Back

All Rights Reserved. Select forumWindowsMac OsLinuxOtherSmartphonesTabletsSoftwareOpen SourceWeb DevelopmentBrowserMobile AppsHardwareDesktopLaptopsNetworksStoragePeripheralSecurityMalwarePiracyIT EmploymentCloudEmerging TechCommunityTips and TricksSocial EnterpriseSocial NetworkingAppleMicrosoftGoogleAfter HoursPost typeSelect discussion typeGeneral discussionQuestionPraiseRantAlertTipIdeaSubject titleTopic Tags More Select up to 3 tags (1 tag required) CloudPiracySecurityAppleMicrosoftIT EmploymentGoogleOpen SourceMobilitySocial Each time you remove an item, try to boot to a floppy diskette and format a diskette.