floppy disk read error Palm Desert California

•on site service NO need to Bring in your equipment •free telephone estimates 760 409 8198 •Senior discounts •MALWARE and virus removal •data recovery and transfer •system setups •shopping services unbiased help to BUY a computer system •network solutions and setups •printers. Faxes. Scanners. WEBCAMS. Point of sale. VOIP •hard drive cloning •annual maintenance contracts available •system backups •cloud setup •video and DVD / digital services •35MM slide scanning / PHOTOBOOKS •tutoring general usage. Microsoft office. PHOTOSHOP •software installations •wireless systems •hardware repairs of ALL types.

Address 68855 Minerva Rd, Cathedral City, CA 92234
Phone (760) 409-8198
Website Link http://desertcomputerdoctor.com
Hours

floppy disk read error Palm Desert, California

or just removing and placing them again.if it was from bios, there would be no read error, it would be simply that hd is not being read, theres a differenceits not Of course it is common to have errors when it comes to the hardware issues and same goes for the BIOS. It's an old drive which I have mostly backed up but there are a few bits and pieces I was hoping to get my hands on fairly quickly. As for the optional disk drive cleaner remember that there is most likely a thin layer of contaminants on the original disks.

With "a disk read error" message,  this is an indication that the IDE ribbon cable or the SATA cable is bad and/or the hard drive is bad. Don't allow them to do any additional software installations except drivers for your sound, modem, and etc. You might want to add AVG Anti-Spyware as well. stander2 , You have to be quick with the POST (Bios) screen otherwise it offloads to the OS.

Next, power down the computer and disconnect the power from the computer and put the CMOS battery back in. (The reason for this step of disconnecting the power again is because Not sure if it works on Windows Vista, but it does for XP and earlier. The software walks you through everything, step-by-step. Verify that the floppy connection is connected to the motherboard FDD connector.

The first thing I would do is call around to different computer shops and stores and get their quotes. Maxtors are very unreliable, I'm surprised you have an old one. The only one who should stop their nonsense is you since you just spout out worthless rubbish.   Also for those wondering the issue is caused by the MFT (Master File When this 'Disk Read Error' pops up, I power off my desktop and swap the drives.

Reports: · Posted 4 years ago Top stander2 Posts: 17 This post has been reported. SHALL I HAVE TO GET YOU BANNED AS WELL?? I thought it was a power surge (though I have a surge protector) but then I didn't notice any of my lights flickering or anything like that. And Ben, Check my post above again since you quoted it, ooopppsss, did you miss it?

Replace the floppy if the floppy data cable did not resolve your issues. After my Windows XP SP2 installation somehow got corrupted, I attempted to reinstall Windows from the XPsp2 CD. While the media is out, I could clean it with a non residual cleaning agent or alcohol. Most 3.5″ floppy disks have a felt-like inner liner which is designed to sweep away surface dirt.

Also, make sure there are no CDs or DVDs in your CD-ROM drive or the DVD-ROM drive before you start your computer! The next step is to leave out the CMOS battery and plug the power back into the computer and power the computer up so that the BIOS can take the change. After the setup files were copied from the CD to the disk and the system rebooted, I get the same message, "A DISK READ ERROR OCCURRED. In this case, a bad RAM memory device is indicated.

The computer is an Intel Pentium 4 about 8 years old. Oh and who the *** are you to warn people? If you plan on reformatting the bad disk, do so at your own risk! Depending on the make of the computers and even laptops have different stages upon repairing the problems.   When trying to re-install Windows XP after having a problem and having to

If the system produces an error message (such as "The system has detected unstable RAM at location x") or a beep code before the single beep occurs, the system has found Reports: · Posted 4 years ago Top Xhi Posts: 6298 This post has been reported. so, put good HDD in as C: made the dudd secondary and booted up in  uBCD4win  that I had made  previously and Ghost saw the dudd HDD. As for repairing the HDD to retain original data.. Good luck.

Checked the bios, everything is detected as normal.2. If the Windows is unable to boot normally, you can use "System Restore", (which can be found in "System Tools" from the "Start" then "All programs" listing.), "System Restore" can also Saturday, April 12, 2008 2:35 PM 0 Sign in to vote Have any of you tried Hard Drive Mechanic recovery software? In the prompt I typed chkdsk with /p /r on the disk in question and they both told me: "the volume appears to have one or more unrecoverable problems".

Also do not threaten people either its a shame MS doesnt have enough mods so they could find the *** that you post and get rid of you. To do a dual boot, you need a barebone system with a motherboard such as the ASUS, Gigabyte, MSI, or other brands. Monday, February 25, 2008 11:02 PM 0 Sign in to vote Mr Random,      You had the CD-Rom and the hard drive reversed. THANK YOU FOR YOUR ATTENTION.

I have never thought of that either. Your SATA hard drive needs to be plugged into the SATA1 output on the motherboard. (Usually, the word SATA1 is inscribed on the motherboard underneath the SATA outlet, or check your Now, I am NOT going to explain any further on how to fix anybody's computers as I have said enough that I posted above here. These problems are called configuration problems, or setup problems.

Because of the technology of floppy diskette drives, it is likely for a floppy diskettes to become bad. Powhammer provides official sounding but ultimately questionable advice.   Powhammer must be a troll.    Q.E.D. I'll only try to intentionally mis-align a standard PC floppy drive instead of a rare 880K Amiga drive. If nothing, then again, it may be the possibility of a bad ribbon cable, replace with new one.

Wird geladen... I'm having the same problem. I could see all of my data and programs. This tells me that for some reason my OS on the drive in question is unable to boot up. Just to let you know, I have fixed the very first computer that came out in a compact size that fits in your home.

Once you are in the BIOS, you need to find the section on the Boot Order. On switching it on this morning, I get the error message: "A disk read error occurred   Press Ctrl + Alt + Del to restart"   If I press Ctrl+Alt+Del, it just DID I SAY THAT I DISCREDIT NORTON GHOST??, NO! RSS ALL ARTICLES FEATURES ONLY TRIVIA Search The How-To Geek Forums Have Migrated to Discourse How-To Geek Forums / Windows XP "Disk read error occurred" message - how do I

After that, you may want to read above for a good installation method or read below to my current postings.     Saturday, April 19, 2008 12:44 PM 0 Sign in to vote