fax protocol error mac Lake Isabella California

We offer In home computer repair with affordable pricing and fast response time. We serve Lake Isabella and the surrounding areas

Address Lake Isabella, CA 93240
Phone (661) 412-3669
Website Link

fax protocol error mac Lake Isabella, California

Retry the fax transmission when the line is no longer busy. 314 The local machine attempted to initiate a remote diagnostic session, but detected that remote diagnostics are disabled on the Configure the remote machine for reception. Save and quit "vi" (enter ":wq")5. "chmod a+rx /usr/bin/efax"Good luck! Error Code(s) Definitions/Causes Solutions 200 The fax session completed without errors.

In the bizhub C364/C284/C224 environment, refer to Here. Disable ECM. This occurs when the line is disconnected or if line conditions degrade during the session. Enable or disable the ECM setting.

error -305 smDisabledSlot: This slot is disabled (-305 use to be smLWTstBad) error -304 smNoDir: Directory offset is Nil error -303 smRevisionErr: Wrong revison level error -302 smFormatErr: FHeader Format is The click, heard for an incoming call, is actually a momentary disconnect of the line. When it re-tries, the same failure occurs.The intended recipient does not receive a fax.NEW CLUESThe new clues came out of my use of the free trial version of the FaxCenter application, Configure the machine to start reception at a lower speed.

error -20000 unknownInsertModeErr: There is no such an insert mode. Errors could still occur, and might result in degraded image quality on the received page. Clear the jammed paper.For information on handling of a paper jam, refer to Here.Is the machine out of toner?No fax can be received if the toner is exhausted. Have the sender send from a different fax machine to see if the error clears. 242 The remote fax machine is attempting to receive instead of send.

error -291 smSRTInitErr: Error; Slot Resource Table could not be initialized. If these transmissions are successful, then notify the user of the remote machine to make them aware of the issue. All other connection indications must be handled either by rejecting them with SndDisconnect, or by accepting them with Accept. Error Code(s) Definitions/Causes Solutions 344 345 346 347 348 349 ECM 350 ECM 351 ECM 352 ECM 353 ECM 354 355 The remote machine failed to respond to a fax command

Wait several minutes between the end of one transmission and the start of the next transmission. 383 ECM Disable ECM, and then try faxing again. I'm going to go back to the system of printing the document and sending it through a stand-alone fax machine (which works very well, but is slow as molasses). One of the few exceptions to this would occur if the remote machine was configured to poll transmit a document, but was unable to receive. Turn both the sending and the receiving machine off for ten seconds, turn them on, and then try sending again.

error -3152 kOTAccessErr: The user does not have permission to negotiate the specified address or options. This discussion is locked Merged Content 1 Level 6 (11,040 points) Q: FAX failure! Works every time - every time being about 2x a year - next to nobody I know uses fax. Privacy Policy © Copyright 2016 HP Development Company, L.P.

error -292 smPRAMInitErr: Error; Slot Resource Table could not be initialized. Being a technological illiterate I don't want to start messing with the /usr/bin/efax system or any other hidden system folder.Thanks for the help.Griff Helpful (0) Reply options Link to this post The user called the correct number, but the machine was configured not to answer. The remote user pressed the Stop key while the reception was in progress.

error -23007 connectionExists: The TCP or UDP stream already has an open connection. error -23009 insufficientResources: 64 TCP or UDP streams are already open. error -23037 ipRouteErr: No gateway available to manage routing of packets to off-network destinations. Sending fax results in error every time.

No solution is available. However, the remote diagnostic versions that are supported by the two machines are incompatible. I [date time] Hint: Try setting the LogLevel to "debug" to find out more. error -3161 kOTFlowErr: The endpoint is in asynchronous mode, but the flow control mechanism prevents the endpoint from accepting any data at this time.

But that leaves you wondering "how do I set LogLevel to debug?"I wrote the following script to help get that done; it allows you to toggle between normal and debug mode or kDMNotFoundErr: Could not find item. To trust the certificate, the certificate must be registered to the system.2241The certificate has expired.2242Cannot connect to the CA server upon certificate verification.2243Time out occurred at the time of the certificate error -23015 openFailed: The connection came halfway up and then failed.

error -3154 kOTNoAddressErr: The endpoint could not allocate an address, or an address was required and not supplied by the client. error -23016 commandTimeout: The specified command action was not completed in the specified time period. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use. Configure the remote machine for poll transmission.

error 26 dsBadLaunch: can't launch file error 27 dsFSErr: file system map has been trashed error 28 dsStknHeap: stack has moved into application heap error 30 dsReinsert: request user to reinsert