fatal error solaris installation program exited Lakeport California

Address 9781 Point Lakeview Rd, Kelseyville, CA 95451
Phone (707) 225-0603
Website Link
Hours

fatal error solaris installation program exited Lakeport, California

This may be caused by the /etc directory being mounted read-only (which can happen during certain types of boot problems). Communication error on send (ECOMM): The link between machines breaks after data is sent, but before the confirmation is received. No such file or directory (ENOENT): The file or path name does not exist on the system. If you do not want to use the on-board raid then we can remove them from raid set so they all show up as individual drive and then once OS is

Open a terminal window. An example of such a system is a "headless" system that is not using a graphics display. Result too large (ERANGE): This is a programming or data input error. Reply Deepa Sreenivasan August 16, 2016 at 12:09 pm Select Root Filesystem type as ZFS instead of UFS.

After the installation of the Solaris software from the Solaris 10 11/06 Software CD - 4, the following prompt is displayed:Press Reboot now to continue. and I just seen the Pass 0 finished, now pass 1 just started so I am good for another 33 hours total for each pair... :) Formatting... Page © 2011 by the Trustees of Princeton University. I/O error (EIO): This references a physical I/O fault.

EDIT: Not immediately deducible, except for the output on the console, but this is stack overflow, so I assume you're doing this in a script. Check for loose connections and otherwise check the network. Near Earth vs Newtonian gravitational potential A Shadowy Encounter Can Dandelion defeat you? If you want to use the disk(s) for the install, use format(1M) to label the disk and restart the installation.Solaris installation program exited.To solve this you need to run the format

Install Solaris using boot media on a sun 5220 not e/w DVD rom... It may have been removed or replaced. share|improve this answer edited Jan 2 '13 at 8:34 answered Nov 19 '09 at 13:08 Oldskool 19.2k63156 11 This also happens if a bash script does not have mode "+x" Soft error rate ...

You are testing a release that contains GRUB software. No such user ... Click here for instructions on how to enable JavaScript in your browser. Unix & Linux Forums > Operating Systems > Solaris Member Name Remember Me?

Framing errors are types of CRC errors, which are usually caused by physical media problems. Protocol family not supported (EPFNOSUPPORT): The protocol has not been implemented on this system. Make sure that the Jumpstart configurations and file shares are correct. If “files” is not the first entry in the “hosts” line of /etc/nsswitch.conf, the hostname lookup will not be possible until the interface comes online.

iSCSI service or target is not currently operational: Run diagnostics on the storage device hardware; check storage device software configuration. It really saved my day, trying to install Solaris 10 on a SUN Ultra 45. capacity of this LUN is too large: SCSI partitions must be less than 2TB. Non-obvious SCSI ID conflicts may be diagnosed using the PROM monitor probe-scsi-all command. (See OBP Command Line Diagnostics for more details.) These errors may also happen when the SCSI device and

So I decided to take the jumpstart approach, but even after installing the jumpstart functions and copy the file on that t5120, it will not work unless I have the MAC Corrupt label: This happens if cylinder 0 has been overwritten, usually by a database using a raw partition including cylinder 0. No message of desired type (ENOMSG): Something attempted to receive a message of a type that does not exist on the message queue. Not found: The specified command could not be found.

PD-bash# ldm add-vcpu 8 ua1 PD-bash# ldm list-domain NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-cv- SP 8 4128M 0.5% 17m ua1 inactive ------ 8 PD-bash# 5.Add 4G Attempting to link in more shared libraries than system limit (ELIBMAX): The executable requires more static libraries than the current system limit. Solaris installation program exited. scorney (TechnicalUser) (OP) 1 Aug 13 06:32 How long should take format & Verify?

Cannot install bootblock: On an x86 system, this error typically appears when a newfs and restore operation was carried out without performing a installboot before installing the OS. and if works fine there is test CD you can download it to check the hardware compatibility on your machine 0 LVL 1 Overall: Level 1 Message Author Comment by:mark_6672012-02-09 share|improve this answer answered Nov 19 '09 at 13:25 apbianco 742 add a comment| up vote 1 down vote 127 - command not found example: $caat The error message will bash: For x64 systems, check the service processor's System Event Log and BIOS log to identify the culprit.

quotactl: open Is a directory: A directory named “quota” can cause edquota to fail. If it was a third party drive then there is a good chance they were never in a sun system and therefore never formatted and labelled. NFS server ... Operation already in progress (EALREADY): An operation was already in progress on a non-blocking object.

They are delivered to the process that caused the signal. Verify the initiator discovery information and storage device configuration. Solaris Interactive Text (Desktop session)" in the menu below. Comments on the contents of this page may be logged to The Solaris Troubleshooting Blog Toggle navigation Questions Tags Users Unanswered Ask question Sign In/Up Solaris Installation Error on V440

Jumpstart? and i edited the /etc/resolv.conf to use my win2003 server dns server.