fastethernet0 0 transmit error Hidden Valley Lake California

Serving The Lake County Computer Community Since 1998 Diagnosing, Repairing & Networking, Personal Computers & Peripherals, for Homes & Businesses.

Address Kelseyville, CA 95451
Phone (707) 279-4103
Website Link
Hours

fastethernet0 0 transmit error Hidden Valley Lake, California

I guess I am wondering if the connection is being dropped on the router-side or the firewall-side. TIA. Have you checked the port on the far end device ?? See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments avilt Mon, 09/08/2008 - 05:12 Other end is connected to ISP side,

Posted by Shane Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest No comments: Post a Comment Your comment will be reviewed for approval. Shall continue to monitor. I appreciate any help on this, it really has me thrown!!! I am not sure the PIX can be hardcoded for duplex but left auto for speed, you might have a speed and/or duplex mismatch which might be causing the issues.

Silent Loop 240mm Becky posted Oct 10, 2016 at 5:37 PM Cyberpower Hyper Liquid 100 GTX... Thanks 0 LVL 50 Overall: Level 50 Routers 39 Message Active 2 days ago Expert Comment by:Don Johnston2009-03-04 I think you're missing what I am trying to say. AMDP2_FE-3-UNDERFLO: FastEthernet0/0 Transmit Error When I run a show int f0/0, it shows an underrun. You mentioned you had a 2514 before, which if I remember correctly is Ethernet (10/half) only and not FastEthernet, so if you have not changed the config on the PIX then

Can anyone give me some hints about this? no network-clock-participate slot 1 no network-clock-participate wic 0 no aaa new-model ip subnet-zero ip cef ! Register now! Also, it is probably a good idea to contact Cisco TAC and see if there is a bug.

See More 1 2 3 4 5 Overall Rating: 3 (1 ratings) Log in or register to post comments avilt Thu, 09/11/2008 - 22:05 I tried both Manual/Auto on my side. No action is required. For Ethernet, this is 51.2us (microseconds), and for Fast Ethernet, 5.12us. The error message is received When traffic level reaches about 2.5 Mb.

I am not >> sure the PIX can be hardcoded for duplex but left auto for speed, you >> might have a speed and/or duplex mismatch which might be causing the ip nat pool pool1 xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx netmask 255.255.255.240 ip nat inside source list 51 pool pool1 overload ip classless ip route 0.0.0.0 0.0.0.0 Serial0/0 ip http server ! Bad network interface cards (NICs) can also cause late collisions. interface FastEthernet1/0.6 > encapsulation dot1Q 201 > ip address X.X.V.V 255.255.255.240 > no ip redirects > no ip unreachables > no ip proxy-arp > no ip mroute-cache > no cdp enable

Blog About Me - My Faith About Me - My Work About Me - Career Story Other IT Blogs Saturday, December 14, 2013 Cisco: What Is A "Late Collision" In A Yes, my password is: Forgot your password? Privacy Policy Terms and Rules Help Connect With Us Log-in Register Contact Us Forum software by XenForo™ ©2010-2014 XenForo Ltd. What's at the other end?

Sun, 09/07/2008 - 23:40 Hi,From Cisco IOS System Error Messages:Error Message%AMDP2_FE-5-LATECOLL: [chars], transmit errorExplanation: Late collisions have occurred on the Ethernet or Fast Ethernet interface. If >> you eliminate the speed and/or duplex mismatch as the problem, then >> open a ticket with Cisco TAC and then can scour the bug lists and see >> if whether its half or full.. Check Point Gaia: How Do I View The Routing Table In CLI?

You've got a duplex mismatch. This can happen if packets queued for transmission were not sent within several secondsHTH, if yes please rate the post.Ankur See More 1 2 3 4 5 Overall Rating: 5 (1 Covered by US Patent. Will 'sh controller fast 0/0' will shed some light on interface hardware ?

I > > left the console on, and am receiving the following error before it > > drops. When a collisionis detected by a station after it has sent the 512th bit of its frame, it is counted as a late collision.Recommended Action: If the interface is a Fast You can check the number of excessive collisions in the output of ashow interface ethernet [interface number]command. I can put us back on the old router and this never happens. > > > > AMDP2_FE-3-UNDERFLO: FastEthernet0/0 Transmit Error > > > > When I run a show int

This traffic level constrain is due to hardware limitation.. Becky posted Oct 14, 2016 at 5:58 PM Fierce PC Dragon Shield Becky posted Oct 13, 2016 at 4:43 PM Fractal Design Define Nano S Becky posted Oct 12, 2016 at As you finish projects in Quip, the work remains, easily accessible to all team members, new and old. - Increase transparency - Onboard new hires faster - Access from mobile/offline Try Join our community for more solutions or to ask questions.

I should ask BT to cut there Line to 10 Half-Duplex? thanks Randy Randy Henson, Nov 9, 2004 #4 Robert B. but even so, you're getting a lot of errors.. Phillips II Guest (Randy Henson) wrote in message news:<>... > I've just installed a new 2600XM to replace a 2514.

Are there any other messages in the logs at the time that the connection is dropping that might help us pinpoint the issue? simon watson, Nov 9, 2006, in forum: Cisco Replies: 1 Views: 753 Walter Roberson Nov 9, 2006 sell two cisco 2600Xm that i used for obtain my CCNP Arnaud P, Jan hostname router ! Please join our friendly community by clicking the button below - it only takes a few seconds and is totally free.

Here is the config: ! so the first thing Id be checking both ends is the duplex.. It's actually a >SonicWall, not a PIX. > >After I set the speed on the ports, it didn't happen as often, but it >did drop a couple of times today, but Phillips II) wrote in message news:<>... > (Randy Henson) wrote in message news:<>... > > I've just installed a new 2600XM to replace a 2514.

Check Point Gaia: How Do I Add/Delete A Static Route In CLI Occasionally, when I cant get into the WebUI, for whatever reason, I'll SSH in and do what I need Samsung stops Note 7 production users should turn off phone [Google] by SparkChaser429.