f02 error code on whirlpool duet Fields Landing California

Address 1655 Main St, Fortuna, CA 95540
Phone (707) 725-6442
Website Link http://www.shawcomputers.com
Hours

f02 error code on whirlpool duet Fields Landing, California

Run the washer in a drain and spin to ensure the pump is running. F/05 Water Temperature Sensor Error If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, disclaimer and Terms of Use. Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect

Next: bench test the pump, if you don't know how, order new--pump noisy. I did a test mode. Ensure the hose is clear by blowing into it. There is only one screw holding it.

Your instructions were so easy to understand. F8E3 Error - Overflow fault. So FYI for those of you who have 7mm screws and not 1/4″. Trap clean out 2.

ft. Subscribe ApplianceAssistant on Youtube! Search Site For Parts Call (877) 338-6774 Like ApplianceAssistant on Facebook! I am still missing a lot of socks....... Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Thanks! 02/13/2015 by Joe C RIGHT ON THE MONEY! Communication error between the main control and the motor control. I did all the above including cleaning out the coin trap, the only thing I found was a small plastic thing about the size of a multi-vitamin and some gunk buildup I rinsed the filter, put the pump back together and....wa-la!

Make sure you are prepared for the water that will flow out of the COIN TRAP. This alone is an indicator that it is somehow clogged. The computer may sense too much soap, and continue to pump. So I stuck my finger in it and sure enough, there was a very thin scrap of cloth, about 1 x 8″, balled up in there.

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the I read somewhere about the switch sensor could cause this if there is blockage. Nothing. Last edited by fredo008 : 07-11-2010 at 08:31 AM. #5 (permalink) 08-05-2013, 11:46 AM bouldervolt Junior Member Join Date: Aug 2013 Posts: 1 Pump access cover This thread

I squeezed it together on the floor and put a plastic cable tie on it to keep it open. WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... Cancel mariaarroz Rep: 1 Posted: 07/04/2014 Options Permalink History We followed the advice here a few years ago when we first had this problem (today is our second time with this Thank you.

If the tub still has water, then the drain pump will run to drain the tub. Once it was cleaned, worked like a champ. Using the guidance above, I removed the lower panel (mine had three bolts) and coin trap cover (be prepared for water) and found a small amount of the expected debris in Browse by Appliance Dishwasher Dryer Freezer Garbage Disposer Microwave Range Hood Range / Oven Refrigerator Trash Compactor Washer Browse by Brand Amana Parts Bosch Parts Dacor Parts Frigidaire Parts Hotpoint

Cleaned the filter and worked 2 times. If the error comes back, it may require you to clean the drain pump filter again. Not enough, I thought, to block the flow. Glad it worked for you:) Reply Amanda says: May 11, 2015 at 3:33 am This worked awesome for me!!

It was filled with water. I am not a handy person by any means, but this worked! I didn't even see that. Is it worth it to keep repairing it or should I just invest in another one that doesn't have so many problems?

I have a 14 month old Duet Sport that has developed a problem which results in a F21 code. While the boot was out, I reached up in the hole and felt a thick wire and it seemed to be loose and rusty. Verify Drain pump operation 2. Was this answer helpful?

I did as he suggested and was amazed at the things found in the trap. Residential Wiring - The Right Way! LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 05-10-2010, 01:46 PM chelseawithmarykay Junior Member Join Date: May 2010 Posts: 1 Whirlpool Duet Washer will not drain Also be prepared for the crap you will find in the trap (ugh).

Took off the piece coming from the bottom of the tub (where there is a ball float valve) and it was completely clogged with a HUGE hairball. My husband was gone (and not due home for days) when I found my machine beeping and flashing the F02 code. You may still have a slow drain problem. If you suspect that excessive suds is causing your problem, let the suds dissipate and then press the PAUSE/CANCEL button twice.

Could not believe the CRUD found in the trap. Click here to visit Merchant's home page. What's New? Check the electrical connections at the pump and make sure the pump is running.

Glad you found the F02 error code post useful. An errant baby sock was jamming up the works here, so glad I didn't have to pay a repair man, as I am mom to four crazy boys… extra money doesn't Remove the 3 Torx head screws (located left, center, and right) from the front bottom kick panel of the washer. Wait a while and see if there are suds.

This should clear the displayed code. F21 is: LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. The part was so easy to put on, I was able to do it all by myself. You probably won't be able to do it with simple pliers because you won't be able to get enough hands inside to make the hose changes.

One thing I have noticed since purchasing this washers years ago...smallish items just like kids socks and such get stuck inside the rubber seal/gasket that you see when you open the Preview my answer Post my answer View Statistics: Past 24 Hours: 62 Past 7 Days: 541 Past 30 Days: 2,812 All Time: 139,311 22,252 Free Manuals 86,937 Solutions 6,444 Devices iFixit