event id 11 driver detected controller error device harddisk1 Carmichael California

Address 1007 7th St Ste 317, Sacramento, CA 95814
Phone (916) 532-1818
Website Link
Hours

event id 11 driver detected controller error device harddisk1 Carmichael, California

Project going on longer than expected - how to bring it up to client? Thanks for sharing… Kelly Mar 30, 2012 @ 03:38:27 Hi, just 2 days ago till now, i got this same error. This will be the first suggestion I provide next time when error id 11 is reported. Since I posted that article I have seen the same error on multiple other computers, and in all cases root cause was hard-drive that is acting up with Misaligned HEAD and/or

By creating an account, you're agreeing to our Terms of Use and our Privacy Policy Not a member? Get the answer julliandg 8 November 2012 17:01:49 haska said:Some sectors may be damaged. Thank you for your answer, I switched it to different port and it seems to be working now. I think maybe this post can help explain how to map between the number and the Hard-disk (look at photos especially), but if you have only one (most common), then there

not very reassuring. 0 LVL 11 Overall: Level 11 Storage Hardware 7 Hardware 3 Windows 7 3 Message Expert Comment by:ocanada_techguy2010-07-02 Honestly, I'm "reaching" and guessing too. PS: As a bonus tip – while I was troubleshooting, I had to reinstall Windows 7 couple of times on various HD drives. So this is normal IMHO. Thanks for any helpful reply...

There was nothing in the card reader, so my computer must be a bit senile :haha: Apr 11, 2010 #9 LookinAround Ex Tech Spotter Posts: 6,491 +183 LOL And Forum The driver detected a controller error on DeviceHarddisk2D. Neither of the first disk in the enclosure get the error (disk 5, or 9) 0 Pimiento OP josephboombox Mar 13, 2014 at 7:20 UTC 1st Post Well They checked everything we did, drivers, diagnostics, etc.

If possible, try another SATA outlet on motherboard or another SATA cable if available. But when i looked online, i find some links about the subject but not good clear and consistent info about it (Maybe someone else might know more? Nothing shows up under that process ID. We shall see . . . 0 LVL 46 Overall: Level 46 Storage Hardware 30 Windows 7 16 Hardware 11 Message Active today Expert Comment by:noxcho2010-07-03 As a last resort

What could it be and how do I stop it? But eventually the disk wakes up and the backup is ok. Tried killing the BESR service, seemed to work eventually but in the end got the error removing with it stopped. 0 LVL 46 Overall: Level 46 Storage Hardware 30 Also, it seems to happen with all three drives.

I wonder if your computer comes equipped with an internal card reader? The backup lasts around 30 minutes, everything looks fine, the Exchange backup seems complete and ready to be restored if needed (that's nice).But once or twice a month, and recently once Once that is addressed, diagnostic utility for Hard-drive will help figure out what is going on with it. Really, what's needed is for Microsoft and Seagate engineer to ensure that in fact that error results in a retry and is LOSSLESS, that would be key, or else the sleep/wakeup

As an aside – DDR3 memory is Ridiculously Cheap. share|improve this answer edited May 13 '15 at 13:21 td512 3,8112830 answered May 13 '15 at 8:37 b-p 1 add a comment| up vote -1 down vote In according https://support.microsoft.com/en-us/kb/159865 please If BESR truly has the drive in use, would that cause the error? or it could be a mobo hd controller and/or driver issue, OR VERY LIKELY usb driver / traffic jam / communications handshake retries related, perhaps significant, or perhaps insignificant "ok to

AMD Detection Driver Error SolvedError message catalyst control center/is is not supported by the driver version Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Heat itself is most likely caused by something else, such as faulty fan on the computer case (pretty cheap to replace). Adi R Mar 30, 2012 @ 12:47:35 Port number changes just from the way your Hard-drive(s) is connected to the motherboard. Usually this error has to do with a Driver.

On computer: COMPUTERNAME DISKPART> list disk Disk ### Status Size Free Dyn Gpt -------- ------------- ------- ------- --- --- Disk 0 Online 476 GB 11 GB Disk 1 Online 59 GB This will let you remove BESR from suspicious list. 0 Message Author Comment by:Jsmply2010-07-02 Well we tried a fresh install of Windows 7 recently, that did not help. just WHICH darn drive is the dud? 0 Pimiento OP harzohrichs Dec 31, 2014 at 4:05 UTC 1st Post i had same trouble,shown device/harddisc2/dr2 after i instaling an I know what device that is causing this because it only happens when I have...

There is no card reader on it. 0 LVL 46 Overall: Level 46 Storage Hardware 30 Windows 7 16 Hardware 11 Message Active today Expert Comment by:noxcho2010-07-01 Can you Every disk will have a device controlling the Raw Physical drive (DR identifier) and a device per each partition, controlling the partition (DP instance) For example: Harddisk1\DR2 and Harddisk1\DP3 Unlike in the case however, there is no common description and there is no map or description of the correlation between these two schema. We have Volumes for C:\ D:\ and E:\ and then one that says *** NO MOUNT POINT *** Ocanada, the external hard drive(s) are not set as index locations. 0

DISKPART> detail disk WD My Book 1130 USB Device Disk ID: 0002DCC8 Type : USB Status : Online Path : 0 Target : 0 LUN ID : 0 Location Path : ByManikle Apr 6, 2010 I went into Event Viewer and see that there is frequently the same error on Harddisk 1 and Harddisk4----BUT I only have 1 harddrive in my computer And according to your last statement. This will be demonstrated using Windows 7 operating… Windows 7 CrashPlan on Windows 7 Video by: Thomas The viewer will learn how to download, install and use CrashPlan from Code42.com on

As for points, it is up to your decision how to assign them. An error was detected on device \Device\Harddisk1\DR25  When I go to Disk management..all I have is "Disk 0"  So does harddisk1 = disk 0  and harddisk2 = disk 1 ?????? 0 Sometimes older motherboards will have some mix of sata ][ ports and sata ]|[ ports. Click Properties.

Apr 6, 2010 #1 LookinAround Ex Tech Spotter Posts: 6,491 +183 Re: those \Device\Harddisk4\DR4 type messages I'm guessing those numeric disk numbers include USB storage devices (e.g. Covered by US Patent. The first part of the .txt output should hopefully contain a list of currently detected storage /Device strings and their associated drive letters. Is it lossless?

It looks like it does occur when the drive is clicked to safely remove.