ftp error 200 type set to Dyess Arkansas

Computer Repair, Custom Built Computers,

Address 111 Thompson St, Luxora, AR 72358
Phone (870) 658-2800
Website Link
Hours

ftp error 200 type set to Dyess, Arkansas

But I cannot access the ftp externally from IE or windows explorer, I get the following errors: "An error occurred opening that folder on the FTP Server. The hosting provider tells me that the has opened port 20, 21, and the range 50000-51000 (for passive mode use). Magalhaes Stefaan Pouseele Blogs Books Hardware ISA Appliances SSL Acceleration Links Message Boards Newsletter Signup RSS Feed Software Access Control Anti Virus Authentication Backup & Recovery Bandwidth Control Caching Content Security My point is that if I download inside list it fails.

Why does the state remain unchanged in the small-step operational semantics of a while loop? Tried to upload the file through Filezilla, uploaded first time. Anyway, so it looks like Internet Explorer doesn't like the Passive IP address you are providing. I directly type ftp://MY_EXTERNAL_IP:8222, complete with USERNAME and PASSWORD and the message appears.

This is what is happening in the given scenario. Only you can prevent flame wars! It uploaded on the second attempt, despite WP saying it had the first time. If I used .each it works.

This is actually two separate mesages that look like one. Why does `parse227` receive wrong response? No issues at all through Filezilla. Look forward to hearing a more technical solution!

If a block is given, it iterates through the listing. This can be attributed to the syntax shown below. Hardware recommendations • RAID5/RAIDZ1 is dead Read my guide! I can see my user can logon, but the message below will appear after logon:200 Type set to A227 Entering Passive Mode(192,168,200,2,199,92)Although the windows firewall is off, I set an exception

Registered in England No 2117968. OR... put: PORT ***,***,20,102,235,136 get: 200 Type set to I. Read the FreeNAS manual.

Status: Server sent passive reply with unroutable address. Read the FreeNAS manual. put: RETR /Filetrack/E-mail_Gateway/_Installer/GA/010_000_003_000/Email Gateway_10.0_Changes_PUBLIC.pdf get: 200 PORT command successful. I have this code in ruby 2.0.0p481 (2014-05-08) [x64-mingw32] file = "/Filetrack/E-mail_Gateway/_Installer/GA/E-mail Gateway_10.0_Changes_PUBLIC.pdf" list = ftp.list('*') list.each{|item| counter=counter+1 counter++ ftp.getbinaryfile(file, where_to_save+File.basename(file)+counter.to_s, 1024) puts "downloaded - .each used" } then in the

put: PASV get: 227 Entering Passive Mode (194,212,10,23,195,93). Message imported from old Serif Forum Posts: n/a What It Is, Is... Make sure you have permission to access that folder. Alan 24th July 2008, 04:32 PM #15 Vicky C Message imported from old Serif Forum Posts: n/a Re:*What It Is, Is...

Remarkable Support." Reply Patrick1972 294 Posts Re: FTP issue on external networks May 17, 2013 03:17 AM|Patrick1972|LINK Hi Cmit, Could it beyou haventopened the ports for your passive range (specified in I updated my question to make it more visible. –Radek Aug 15 '15 at 11:33 Can you try the way I suggested now and tell me if you see The hosting provider tells that I must have another problem in my installation somewhere and I need to find it out. There was no error message and it didn't take any longer than usual, though.

Status: Connection established, waiting for welcome message... So if there are packet losst, I don't know how to see that in this case here. Some more good news is i can use the ftp ipaddress command in cmd and i get logged in without issue. FTP Error Type 200 set to I explained.

FTP error means that the server experienced or received an error of some kind in the previous file/data transfer from your computer going to the server. put: TYPE A get: 200 Type set to A. Word for someone who keeps a group in good shape? Hardware recommendations • RAID5/RAIDZ1 is dead Read my guide!

How much interest should I pay on a loan from a friend? The results of ftp.list are similar to the ones you get with the command ls -l, so I don't think the FTP server you are interacting with will consider something like Would you like to answer one of these unanswered questions instead? I have server 2008 enterprise and I am trying to get an ftp site up and running.

Grr! You might want to look into it as well. Browse other questions tagged windows-server-2008-r2 nat ftp passive or ask your own question. Cory Granata Please "Mark" as Answer if this post helped you.

It answers common questions newbies to FreeNAS have. I don't think it's a bug, more a limitation of the current software. Contact Us - Serif Forums - Archive - Top Contact Support Affiliates Serif Store Careers Press Terms & Conditions Privacy Desktop Publishing Software Website Design Software Photo Editing Software Video put: LIST * get: 125 Data connection already open; Transfer starting.

But you wrote that the Windows firewall is off, so I suppose it is a problem of the external firewall/router (also check the client side). All rights reserved.