frigidaire stove f10 error code Siloam Springs Arkansas

Address 1270 Highway 412 W Ste E, Siloam Springs, AR 72761
Phone (479) 549-3663
Website Link http://www.pcconnection.com/blog/launch-of-new-connection-brand
Hours

frigidaire stove f10 error code Siloam Springs, Arkansas

With the diagnostics above, I was able to pretty quickly determine that the EOC was bad. thank you for using manage my life. 1 Share theConversation Click to Chat We're available to chat FAQs Check out the most frequently asked questions Video How to use the site The time now is 06:33 PM. Any suggestions?

Ok basically what the F10 is telling you in this case is the oven is over heating. If you order them from AppliancePartsPros.com, you can return unneeded part later with full refund. Gene. Valerie, you posted your first question on the front page: http://www.askgene.com/ and I replied on the same page.

Logged jumptrout51 Technician Member Since: Nov 2007 Posts: 1879 Country: Re: Frigidaire gas range error code F10 « Reply #3 on: February 06, 2009, 02:49:17 PM » You main electronic control, Make sure there are no broken wires and all connections are tight and firm. Rating is available when the video has been rented. Some of the teeth came out of the little black plastic end cap.

F95 Door motor mechanism failure. Sign in 72 7 Don't like this video? applianceassistant 608,627 views 6:52 Diagnose Kenmore Range Error Code E1 F2, EASY FREE FIX FOR MY RANGE! - Duration: 1:18. Gene.

The part number for the temperature probe is 316217002 The part number for the EOC is 318414213 Good luck. Contact the seller and request the replacement. Disconnect the power to the oven. the oven temperature sensor can be removed and tested for resistance and compared to the rtd scale in the image below.

Is it something that an amateur could easily do? Transcript The interactive transcript could not be loaded. Ed Gene // Apr 23, 2015 at 9:29 pm Hello Ed, Thank you for your question. Gene.

Replaced it and was back in business. You may need to replace the overlay as well. F3 or F30 - Open/shorted sensor (RTD probe) connection. Model Number: 970686132 Brand: Sears Kenmore Put oven on and cooked our food for 90 mins then all of sudden f10 error.I have to say the oven seemed alot hotter then

Oven temp started to climb and would not shut off. Locate the two pins in the plug at the EOC that are connected to the sensor. The oven control board may think that the oven is hotter than it actually is, which is why you may see this code when the oven is off and at room Mike Ask Your Own Appliance Question Customer: replied6 years ago.

Remove the rear panel and locate the relay board. Ed Gene // May 6, 2015 at 9:35 pm Hi Ed, Put everything back together and give it a try. In such situation I'll need the complete model number of the oven. If not, I understand that it is likely either the thermometer or the panel.

Ken Gene // Dec 26, 2014 at 1:53 pm Hello Ken, Looks like the cause of the problem is a faulty EOC. code goes away immediately upon opening the oven door. There are two different potentiometers with the ESEC control system. Judy // Mar 31, 2015 at 5:11 pm Hi Gene- Thank you so much for the time you put into helping folks with appliance issues!

Thank Mike, you've been very helpful! I can't help but worry there is a bigger issue, this time this was NOT relatively close to a self clean, which I have read can be a cause of electrical Thank you in advance!! Just in case you will decide to get new control panel, the part number for the control panel is 316538405 Good luck.

The motor does not stop rotating.  Press stop key. Here is my previous reply: "Hello Valerie, Thank you for your question. We just had a something similar to what happened to Len yesterday. If the sensor checks no continuity, an "OL" reading on this meter, it should also be replaced.

Thanks Reply With Quote May 26th, 2011,11:33 AM #6 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,575 It was 1 hr into baking and the temperature did runaway, everything was black. Check for shorted Sensor Probe harness between EOC & Probe connector. John // Apr 7, 2015 at 2:06 pm Hi Gene, I pulled the EOC and the keypad is held on by double sided glue, it is a two piece.

I can push the button in that turns off the oven light and makes the oven think the door is closed, and it will immediately start beeping and showing F11 again. Residential Wiring - The Right Way! If this is your first visit, be sure to check out the FAQ by clicking the link above. Do not forget to turn off the oven circuit breaker prior to any disassembly.

Cut off the wires at the plug which goes to the EOC, leaving about 3″ to 4″ to splice a new wires. If the reading at the sensor is the same as reading at the EOC plug, the sensor is defective. Your stove is new and suppose to be covered under manufacturer warranty. When I test those two part on it I get the same results.

Gene // Dec 19, 2014 at 11:35 am Hi George, I believe the relay board will solve the problem.