event viewer error 11 Cherokee Village Arkansas

Promise Electronics was established in 1989 in Jonesboro, AR.  However the owner and technician for the company, Dave, has had over 30 years of experience in television and electronic repair.  Dave has had extensive training by most major manufacturers and has continued his training to this day.

Address 3844 Highway 62 412, Hardy, AR 72542
Phone (870) 847-4750
Website Link
Hours

event viewer error 11 Cherokee Village, Arkansas

I then swapped out > the SATA cables on the HDDs with new ones. There's about half a dozen errors each time the drive is removed. Solution: New motherboard - and I was back in business the next day. Please replace Cache board.

The event will be logged for each device included in the bootable RAID array". Your name or email address: Do you already have an account? Tired, May 28, 2012 #6 Ian Riches Guest In article <-september.org>, says... > My event log has many errors of the form: > > Event ID 11 Source: ATAPI > Chipotle Apr 27, 2015 Nigel M Manufacturing, 1-50 Employees I'm seeing this on clean removal of a USB drive.

I do not know yet if the problem is with the Noontec hub or the Shintaro drive dock. It has two 1 TB Samsung HDDs (not RAIDed or >anything) and a single optical drive connected to the on-board SATA >connectors via IDE mode (not AHCI - it's not available x 275 Corey Monteiro Boot-up was also very slow when these errors began to occur. It could be that port is sata 2 now, but most likely so is your hard-drive - and either way that ridiculously fast sata 3 is only relevant for newest SSD

Both 1TB drives are showing no SMART errors logged, and pass SeaTools for DOS tests with no errors thrown up. The error is suggesting an electronics problem. ::: :::: Should I be worried? ::: ::: Make sure your backups are up to date, certainly! ::: ::: Is it always IdePort1? When Windows loaded and this Event ID appeared, Windows took a long time to start up (even when the swap file was moved to the C: drive). x 307 Anonymous I got this error in my event viewer along with these: Event ID: 129 Source: HpCISSs2 Description: Reset to device, \Device\RaidPort0, was issued.

Microsoft has published several articles about this and other related errors. Advertisement Tonyho Thread Starter Joined: Oct 1, 2012 Messages: 2 This error has been reported before in the forums, but I could not find a solution that worked - changing SATA When a physical sector of the disk is read by an application (e.g. After a while the D: drive failed.

Comments: Sf4000 We had it due to failing battery on PERC 6/i. If you choose to participate, the online survey will be presented to you when you leave the Technet Web site.Would you like to participate? If you have only one drive, ensure you do not have it configured to cable select and update to the latest IDE drivers from your motherboard manufacturer". They both have a qlogic 1040b scsi adapter, directly connected to digital ba356 scsi storage box.

When I bypass the hub and go straight to the PC it does not happen. Vincent und die Grenadinen Südafrika Surinam Swasiland Tadschikistan Taiwan Tansania Thailand Togo Trinidad und Tobago Tschad Tschechien Tunesien Türkei Turkmenistan Turks- und Caicosinseln Uganda Ukraine Ungarn Uruguay USA Usbekistan Vanuatu Venezuela The Event Viewer displays an Atapi error 11 along with continuous freezing which gets really annoying. could this be the reason?

Logged a case with HP and they asked me to run the Array Diagnostic Utility. At the same time, transfer rates to the hdd in question became very slow. I found the cause to be a USB Compact Flash card reader. Matthew, Dec 1, 2010, in forum: PC Hardware Replies: 7 Views: 352 Jon Danniken Dec 2, 2010 Clonezilla does not work with Windows 8.1 in cloning disk(disk-to-disk clone) RayLopez99, Oct 27,

Win 7 Atapi error 11 Discussion in 'Hardware' started by Tonyho, Oct 1, 2012. Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc. Turn off autoplay for the device to limit the errors. My event log has many errors of the form: Event ID 11 Source: ATAPI The driver detected a controller error on \Device\Ide\IdePort1 Sometimes I go for a day or two getting

Show Ignored Content As Seen On Welcome to Tech Support Guy! It reported a warning related to a SMART factor that could indicate a bad cable. DigDeep Dec 28, 2012 @ 14:20:21 I had this problem too. It will provide extra logical data integrity layer above controller, so will alert you on the spot about how your integrity is fairing.

Its a shame that neither the Seagate nor WD tools reported that issue and showed the SMART status always as green... We are a friendly community of computer technicians, hobbyists and those seeking some tech advice - our expert members are helpful, encouraging and very willing to assist! Turns out it was using slower PIO by virtue of it being older HDD. Do I need them?

I'll try replacing the sata tomm… Asad Dec 10, 2012 @ 00:09:32 Hi Adi, I just wanted to thank you very much for posting this solution. If you are in a budget crunch, one potential workaround is to slow down your HD to use different PIO. Join over 733,556 other people just like you! I think maybe this post can help explain how to map between the number and the Hard-disk (look at photos especially), but if you have only one (most common), then there

Changing between startup items and services to see if there was any problematic service or startup program didn't work, so I presume there must be a driver, which isn't loaded in Once that is addressed, diagnostic utility for Hard-drive will help figure out what is going on with it. I knew it had to be a hardware issue because i had Win7 running fine for a few years. It finally turns out that the culprit is the USB CompactFlash reader attached to my machine.

Loading... Does this have any impact on performance?? After restarting the machine a few times, I thought to check the event log. Most of these drives were under warranty and once replaced by manufacturer, the problems disappeared.

Pity I spent so much time >testing everything else in the system first! >Cheers, I see there are sata testers out there - but looks like they test ion the power