event id 11 source disk type error Canehill Arkansas

We are a full service computer repair shop in Fayetteville, Arkansas, specializing in affordable computer repair for the NW Arkansas area. We remove viruses / spyware, install software, upgrade hardware, recover data, setup networks, repair PCs and Macs, towers or laptops. We specialize in strange problems, bringing slow computers back to life, and saving you $$$.

Diagnosis, Malware Removal, Broken Screen Repair, Data Recovery, Hardware Installation, Upgrades, Data Cloning, Backups, General Repair, etc..

Address 4210 Frontage Road Ste. 14, Fayetteville, AR 72703
Phone (479) 422-7574
Website Link http://kmotiv.com
Hours

event id 11 source disk type error Canehill, Arkansas

Is there such device listed at all? 0 Message Author Comment by:Jsmply2010-07-01 Hi Noxcho. Join Now For immediate help use Live now! One user solved this by disabling DMA in the BIOS and disabling the Write Cache in Windows 2000. Good stuff! 0 Chipotle OP [email protected] Jul 24, 2013 at 4:57 UTC 1st Post As far as I remember, DR represents the Raw physical drive and DP represents

Will have your info from mountvol and will check indexing in 5 minutes and will post again. 0 Message Author Comment by:Jsmply2010-07-02 Noxcho - ran Mountvol from the command prompt. I was able to fix this problem. Dell is equally puzzled eh. What was causing the errors happened to be the hard drive carrier.

Also look this MS object: http://www.microsoft.com/technet/support/ee/transform.aspx?ProdName=Windows%20Operating%20System&ProdVer=5.2&EvtID=11&EvtSrc=disk&LCID=1033 BTW, do you have card reader device in this machine? 0 LVL 46 Overall: Level 46 Storage Hardware 30 Windows 7 16 Hardware 11 Covered by US Patent. Just want to make sure in the long run these errors won't account to bad data the day we go to retrieve a backup off the drives. x 315 Alexander Freudenberg In certain conditions, this error message is related to the S.M.A.R.T attribute 187 (Reported uncorrectable errors).

The most prominent omission from your valuable contribution is the Microsoft troubleshooter. Are "ŝati" and "plaĉi al" interchangeable? SBS Server Windows SBS migration to essentials and Office 365 Document Collaboration Evaluate SharePoint 2010 & EMC CenterStage to replace Documentum eRoom. After running the tool (no downtime is required), the report show this: SLOT 0 Smart Array E200i Controller ERROR REPORT: Array accelerator status: Valid data found at reset Hardware Problem

They seem to think it's either related to the Seagate drive sleep setting, or just the way the bridge card on the drives work. Maybe it's a combination of windows and drivers and hardware sort of timing-out that all just happen to coincide. x 309 W4tch3r I am getting this error using multiple drives in a Shintaro USB3 drive caddy. cue Fred Flinstone "friger frickin...

Get the answer evongugg a b G Storage 30 December 2009 00:56:18 Check disk numbers in Control Panel->Disk management. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. We can check that this evening. 0 Message Author Comment by:Jsmply2010-07-01 Going to go now and do the swap on-site so we can get a first hand answer. This new drive (connected today) in the rotation had not been changed yet to the new sleep setting in the Seagate firmware.

Lucia St. The system returned: (22) Invalid argument The remote host or network may be down. The error description reads as follows: The driver detected a controller error on Device\Harddisk#\DR#. More importantly, do you anticipate long term harm on the drive this way? 0 LVL 46 Overall: Level 46 Storage Hardware 30 Windows 7 16 Hardware 11 Message Active

As such, it is outside the usual user-mode process space, but it's called "System" in Task Manager and some other tools, as a convenient name." I think that System Volume Information Since then I have traced the problem to the HD caddies I had my drives in, which until last week worked fine. Join the community of 500,000 technology professionals and ask your questions. This will let you remove BESR from suspicious list. 0 Message Author Comment by:Jsmply2010-07-02 Well we tried a fresh install of Windows 7 recently, that did not help.

x 321 Curits Hays I have a drive enclosure from Lantec for an IDE drive. Thanks in advance for any feedback. Re: Disk and symmpi Event log errors: driver detected a controller error on \Device\Harddisk1 ericsl Jan 18, 2011 7:47 AM (in response to continuum) Hmm, I am looking at the log Even some graphics "share" memory with the the mobo and if said memory were swapped by virtual memory management (ever see a graphics card painting the screen reallly slowly, then speeds

All rights reserved. Please try the request again. After changing the setting, there were no errors throughout the weekend. Disaster Recovery Hardware Storage Hardware Storage Software System Utilities Storage 102: more concepts of the IT enterprise storage Article by: Carlos This article is an update and follow-up of my previous

Downtime on this server is not an option. No issues.I ran Shrink and the server coughed up a stop error and rebooted.I am attaching the logs from the guest OS.TYIA,~E vmware-mcts1.log.zip 19.6 K Like Show 0 Likes (0) Actions I will check the registry this evening when the machine is not in use. And sure the event log was giving various errors. 0 LVL 46 Overall: Level 46 Storage Hardware 30 Windows 7 16 Hardware 11 Message Active today Expert Comment by:noxcho2010-07-01 The

We have Volumes for C:\ D:\ and E:\ and then one that says *** NO MOUNT POINT *** Ocanada, the external hard drive(s) are not set as index locations. 0 I won't do it on the server having the issue.I will certainly copy the entire guest vm prior to doing anything. recollect the elephant? x 352 Anonymous I got this error after buying a new power supply.

If the shrink doesn't work then I can also clone the disk or convert the machine.Thanks for your help so far. I did use Handler from technet to see what has the drive open. Although a write using a consumer grade drive my complete successfully, the RAID controller will report a timeout. I change it so each drive was on its own IDE physical connection, and put my CDROM on the second channel as slave.

It's not a warning like the paging error in XP, this is an actual error. Possible solutions include: Uninstall the Intel driver and reinstall after Roxio EZCD Creator, simple do not use the Intel driver. One more drive in the rotation to change (tomorrow) and hopefully they will remain problem free.