ford truck error code invalid exaust Pirtleville Arizona

Address 1326 San Jose Dr, Bisbee, AZ 85603
Phone (520) 266-0110
Website Link https://www.onforce.com
Hours

ford truck error code invalid exaust Pirtleville, Arizona

I saw a suggestion on another Ford forum (I lost the site name) that said to try adding Chevron techron to try fixing the problem. Yesterday 05:50 PM by CatSkinner 1 1984 f250 engine stops... realfixesrealfast 483,516 views 8:11 P0401 2002 F150 EGR System Overview and Troubleshooting Guide - Duration: 21:27. intermittent Harness routing, charging ckt., sensor, int.

Test the Delta or Digital Pressure Feedback EGR Sensor (DPFE) with a data streaming scan tool and verify that the amount of exhaust backpressure voltage or percentage changes according to spec FFR3 sends an incorrect value. plz hlp me any one .. Failure of the master control unit with the results of the processing unit. 3858 temperature sensor the amount of oxygen in the exhaust gas (lambda probe).

The time now is 05:20 PM.

-- FTE_updated Guidelines - Contact Us - Ford-Trucks.com - Archive - Advertising - Cookie Policy - Privacy Statement Looks like the stealer screwed up the programing!!!! EGR systems are used to reduce the combustion temperature, thus reducing NOx formation. Checking charge air pressure, checking the reliability of the connection contacts.

High or low temperatures. Messages from EDC1, EDC2, EDC3 unit FFR available. 3804 Error in sending messages on the CAN1 (FFR / EDC-CAN). Slave control unit blocks the supply of fuel until the connection is restored. performance Circuit failure, faulty solenoid, PCM P0743 Torque converter clutch system electrical Faulty solenoid, circuit, PCM P0750 Shift solenoid A malfunction Circuit failure, faulty solenoid, PCM P0755 Shift solenoid B malfunction

Tampatec 7,520,033 views 4:02 P0401 EGR Valve Port Cleaning - Duration: 5:13. Check the supply voltage, the voltage of the sensor signal. 3852 Identification of the AGR on the temperature. Check sensor readings during operation. 3813 starter protection device. Once the code P0402 has been retrieved with a scan tool, the freeze frame data should be documented and analyzed in order to determine what engine conditions were present when the

And any other DTC code that appears on the dash is going to correspond to the second column of the data below, any other codes aren't displayed on the dash, you'll In that case you possibly have a defective lift sensor, or EGR temp sensor. Checking the output stage for an open or short. 3748 output stage (Highside) unit dosage high-pressure pump. Check the voltage on the subject is out of range. 171 Ambient temperature.

P0400 Exhaust Gas Recirculation Flow Malfunction P0401 Exhaust Gas Recirculation Flow Insufficient Detected P0402 Exhaust Gas Recirculation Flow Excessive Detected P0403 Exhaust Gas Recirculation Circuit Malfunction P0404 Loading... Deviation injection volume on the appropriate cylinder. 3739 Non-uniformity in the cylinder. FFR1 sends an incorrect value. 3020 FFR1: Invalid message due EDR (limiting the maximum speed).

Misfiring on several cylinders. 3830 Irregularities in the ignition. Perhaps one of the sensors is defective. 609 Module CAN 1. Autoplay When autoplay is enabled, a suggested video will automatically play next. There is no communication with the unit or FFR FFR asked EDC standalone mode.

i hope that will help GT Stang is offline Quote Remove Advertisements Sponsored Links Ford Forums Advertisement Reply Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and No connection with the OBD connector. Faulty starter, starter damaged wiring, faulty starter relay switching (IMR). Please try again later.

I could try to buy the correct sizes tires or a programmer that will completely void my warranty. These are stored in response to a problem found in the car by the system. I have no symptoms other than the CEL being lit and a lot of engine noise. P1261- P1268 High to low side short cyl. # 1-8 Short circuit, shorted injector, failed IDM P1271- P1278 High to low side open cyl. # 1-8 Open circuit, open injector, failed

Check wires and connectors fault, checking the accuracy of the sensor readings. 3837 Control of the amount of oxygen sensor in the exhaust gas values (lambda probe). The pressure relief valve is open. Slave control unit blocks the supply of fuel until the connection is restored. Open (FMI4) or short (FMI1) in the injector circuit.

What is its purpose?2 answersJanuary 10, 2011Related ItemsEGR system clean.egr valve replacement/cleaningwhere is the egr vavleegr valve blows a hole makes load noise and slows car down to about 40 miles Follow scan tool manufacturer's operating instructions to access the Diagnostic Trouble Codes (DTC's). It is considered a high temperature above 800 ¬į C. Check valve.

Posted by FFR to select the characteristics of the smoke when the system is off exhaust gas recirculation. 3785 particulate filter PM-Kat (solids catalyst). FFR2 sends an incorrect value. The codes should be used in conjunction with the vehicle's service manual to discover which systems, circuits or components should be tested to fully diagnose the fault. Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > Ford Cars and PAG Vehicles > Ford Focus Forum > DTC Codes Reply Tweet LinkBack Thread Tools

Should I not have the speedo corrected or will just changing the tires give the error code??? Check if the rate of temperature change, test leads and connectors. 175 fuel temperature. Check the supply voltage, the voltage sensor signal and accurate readings. 3920 NOx concentration. Check the supply voltage, the voltage sensor signal and accurate readings. 3944 temperature charge air intercooler after a low pressure.

If you find one missing let us know and we we'll add it immediately! He said there are only 2 sizes to choose from in the PCM of a 2011 Eco FX4 either 275/55/20 or 275/65/18. Check 3820 CAN1 (oil temperature and the ambient air). Check the supply voltage, the voltage of the sensor signal. 3091, coolant temperature sensor.