frigidaire professional series oven error f30 Shorter Alabama

Address 410 N Eastern Blvd Ste D, Montgomery, AL 36117
Phone (334) 271-3629
Website Link http://www.pcwonline.com
Hours

frigidaire professional series oven error f30 Shorter, Alabama

Gene // Dec 18, 2014 at 7:58 pm Hello Jim, Sorry for the delay. The ribbon you mentioned earlier is a part of EOC and has nothing to do with the overlay (keypad). If the reading is correct, the EOC would need to be replaced. You can do it using a simple and inexpensive clamp-on meter 600-CF If you don't like it then just replace the oven igniter.

However, a quick glance at page 12 of the Factory Parts Catalog's wiring diagram (http://www.youserguide.com/wiki/Frigidaire_PLES389ECH or http://www.serviexcell.com.mx/manuales/PLES389ECH.pdf) shows two thermal breakers wired into the circuit as well. Most error codes are generated as a result of irregularities in the power supply or usage. ft. Gene.

Where did you get the EOC you replaced recently? I attached the link below. F62 Missing zero-cross signal Replace the EOC. F31 Shorted sensor probe or wiring problem.

The good part of this sad news is that you got nice opportunity for a good New Year (or may be it's not too late for Christmas?!) present to your wife The part number for the EOC is 316418735 To order a part just click on the part number. Contact the seller and request the replacement. If the door lock motor never stops rotating, or if the F95 error comes back again, verify wiring of the motor.

thanks josh Gene // Apr 10, 2014 at 5:03 pm Hello Josh. Thank you! no sorry Expert: MRANSWER replied4 years ago. In situation you described most likely the EOC has failed and would need to be replaced.

The part number for the EOC is 316557115 You also may want to replace the overlay. By Kristinemomof3 in forum Dishwashers Replies: 1 Last Post: July 8th, 2007, 07:57 AM Tags for this Thread thermostat View Tag Cloud Posting Permissions You may not post new threads You Appreciate any help! Ask Your Own Appliance Question Customer: replied4 years ago.

Remove the oven door as instructed in the Owner Guide and inspect both hinges. Valerie, you posted your first question on the front page: http://www.askgene.com/ and I replied on the same page. Gene. Do you have a test meter handy?

wall oven, following your directions I measured the sensor resistance which was 1077. Thank you for your question. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual 50385155-434c-467c-aabc-0a989e4fbb16.p... Gene.

Room temp 23c.If this has been helpful please press accept. F8, F9 or F90 - Lock motor switches improperly positioned. Ken // Dec 29, 2014 at 9:59 am Hello Gene, Thank you, you always answer quickly. Oven temperature sensor - What a common sensor or temp sensor looks like.

I understand your point but only replacement of the EOC would fix the problem. The burners work fine, oven cannot be used. model plgf389cce Frigidaire professional series Gene // May 17, 2015 at 6:34 pm Hello Greg. I'm lucky because it did not happen to me, but I have heard about such problems.

Control may have shorted relay, RTD sensor probe may be bad. Jay // Sep 2, 2015 at 11:53 am Gene, I have a Frigidaire FEF368gba with F10 code coming up. If this error code shown while the oven was in day time mode, the EOC would need to be replaced. Code f10.

do you still suspect the relay board 316443925 ? Ken // Dec 24, 2014 at 4:00 pm Gene, Merry Christmas. It may have an open connection or just plain defective sensor. F95 Door motor mechanism failure.

Good luck. If fault returns after reconnecting power, replace the EOC. Expert: Tom Johnston replied5 years ago.